メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

右側スピーカーを交換するにはこのガイドをご利用ください。

このガイドは通常通り起動しているMacBook Proノートブックの右側スピーカーを交換します。

  1. 上部ケースと底ケースを留めている次の10本のネジを外します。
    • 上部ケースと底ケースを留めている次の10本のネジを外します。

    • 2.3 mmペンタローブネジ−2本

    • 3.0 mmペンタローブネジー8本

    For all the screws you use the P5 pentalobe screwdriver?

    Carlos - 返信

    Pentalobe is only for the screws on the bottom cover. The Torx screw driver is for the remainder.

    Fredrik -

    Is the Pentalobe screwdriver mentioned in the tools list? I did not have one so I used a filed down flat blade screwdriver. Not a fantastic idea, but it works.

    Alex Birkett - 返信

    Yes, it's mentioned on the top of this page. P5 Pentalobe to be precise. I didn't have one either, so I bought one from iFixit and that works fantastic. An absolutely precise fit, which is important especially when you might open your MacBook a couple of times during the years you own it. Not using the correct tool might do more harm to the screws than you want! I once had this with a Lenovo Yoga 3 Pro, which has Torx screws (T4 I think) and I used cheap Chinese quality tools, with the result that both the tool and one of the screws are damaged.

    addvariety -

    the macbook in the picture is 2012. does it has the same structure as 2013?

    Edison - 返信

    I never, ever, ever considered using anything but the correct tool on the Pentalobe screws. Too easy to strip and void your warranty (if still in effect), as well as make it almost impossible to get inside later for another upgrade or repair. The Wiha P5 Pentalobe screwdriver fits like a glove and costs only about $11 (a fraction of your drive's price)at Amazon.com. Get it!

    marketing - 返信

    is P5 supposed to be for all 10 screws? it works on the 2x 2.3mm at the top, but not for the 8x others for me. what size screwdriver for the 3mm? thanks

    monsieurescargot - 返信

    Yes, the p5 works for all 10 pentalobe screw heads for bottom cover. The the different size mm reference only refers to the difference in length of the screws, but again both heads are p5.

    Antoine Thornton - 返信

    I followed this exactly and was able to replace my broken trackpad. I did not have to replace the ribbon OR the battery. However I would suggest getting the ribbon since it’s fairly cheap, as for the batteries I was able to do it with a card only. I didn’t use any heat or the liquid but it takes some time. You really have to work the card in there to release the glue. Also you must be very careful not to bend the batteries or damage them, if you do you must replace with new. This took me about 1.5hrs and my computer works like new. Apple cost for this job was around $450, I did it for $120. Big ups to ifixit for this awesome tutorial, tool set and parts!

    On a side note, only use quality tools, the cheap ones will break or strip the screws.

    Dustin Steward - 返信

    Note that the eight 3mm screws have a shoulder under the head, while the two 2.3mm screws are “full thread”, i.e., there is no shoulder under their heads. It’s important to put the two screws with no shoulder at the hinge of the cover.

    All ten screws require a P5 Pentalobe screwdriver, preferably with a magnetized tip to help hold and position the screw.

    All of the screws have blue “Loctite” thread locker compound on their threads. This is to help prevent the screws from working loose and falling out. Don’t attempt to clean the Loctite from the screws — leave it in place, and it will continue to help prevent the re-inserted screws from working loose.

    When replacing the bottom cover, it is a good technique to insert and BEGIN tightening all ten screws BEFORE fully tightening any one screw. After all the screws have been started, then go around and finish tightening all of them. By doing this, you make it easier to feel that each screw has been started properly, and is not “cross-threaded”.

    doubleclutch - 返信

    This is what I found on my MBP mid-2014 13” Retina. All 10 used the same screwdriver. I didn’t see the blue “loctite” but I also got my computer refurbished.

    Evan Shulman -

    A good technique for starting to thread the screws when replacing them is to position and align the screw, and with the driver, gently turn the screw in the REMOVAL direction until you feel and hear a slight click. This click happens when the leading thread of the screw drops off of the leading edge of the thread in the hole — this is the point at which the threads are properly positioned for engagement. You can now turn the driver and screw in the TIGHTENING direction. This technique will help prevent accidental “cross-threading” of the screw, which will damage the threads permanently.

    Note that this is a useful technique when installing ANY threaded fastener.

    doubleclutch - 返信

    Just finished replacing my battery (MacBook Pro 13” early 2015), glad I did, the old ones were noticeably swollen. I was surprised to find the battery at 57% upon completion and charging the new battery. No problems with replacement however, kit arrived without the Pentalobe driver. I got a nice complete kit from Amazon for 20 euro in 2 days. iFixit offered a coupon on any future purchase but right now, I have no plans on needing anything. Nice gesture but would have preferred the driver in the kit in the first place.

    Suggest having a small can of compressed air on hand to clean out the interior, after 4 years, mine was quite dirty. Ear buds and alcohol were the best I could do. And a magnetized driver is mandatory I think.

    D M - 返信

    REQUIRED PARTS (SCREWS) TO DO THIS JOB UNAVAILABLE HERE:

    If your keyboard is riveted to the chassis as mine is, Late 2013 MBP 13” retina, you need about 100 screws to reattach the new keyboard.

    ifixit does not have them. I did just now find them at Beetstech for $4.50 along with a back light $13 for the keyboard in case you want one. It looks like Beetstech is a big competitor of ifixit with an excellent reputation (like ifixit has) too. I just ordered these parts and will not happily be moving forward with my keyboard replacement.

    Timothy Hardman - 返信

    Fun Fact: I got three of the 2,3 mm Pentalopes … ;-)

    Paco Demant - 返信

  2. 上部ケースと底ケースの間に指を差し込みます。
    • 上部ケースと底ケースの間に指を差し込みます。

    • ゆっくりと底ケースを上部ケースから離していきます。

    This takes a bit more effort than you might expect. Put your fingers where shown and lift about 3inches. With enough upwards pressure the plastic holders will “pop free” and the bottom will come off easily.

    hamiltont - 返信

    Agreed. A decent amount of force is required here.

    Evan Shulman - 返信

  3. 底ケースは上部ケースと2つのプラスチック製クリップで中央付近に接続されています。 再組み立ての際は、丁寧に底ケースの中央を2つのプラスチック製クリップに接続するように押し込んでください。
    • 底ケースは上部ケースと2つのプラスチック製クリップで中央付近に接続されています。

    • 再組み立ての際は、丁寧に底ケースの中央を2つのプラスチック製クリップに接続するように押し込んでください。

    There are two screws that are shorter-they go to the back near the vent.

    wrbandllm - 返信

    This was already mentioned at the start, it says 2x 2.3mm screws and those are coloured red instead of orange for the other ones in iFixit's image.

    addvariety - 返信

    What is the black vinyl-y sticker on the inside of the case (some sort of shield?). I was forced to slightly puncture it in order to replace the feet on my laptop. Thanks in advance.

    Tommy Huang - 返信

    When I got the back off, I found this piece loose, any idea what it is? about 9mm long frosted plastic

    https://imgur.com/a/tYaxGdG

    Fred Anderson - 返信

    This wording I found quite confusing. They just mean when putting the lid back on that you just removed in the previous step, push here.

    Mmm ttt - 返信

    I took my pointer and thumb (which are luckily long enough) to feel where the studs are on the back panel, and then as I put the back panel back on, I pushed in the spot I had marked with my fingers to ensure I was applying pressure only on this part.

    Evan Shulman - 返信

  4. 必要に応じてバッテリーの接続ボードに留められているプラスチック製カバーを外してください。
    • 必要に応じてバッテリーの接続ボードに留められているプラスチック製カバーを外してください。

    Do you know where I can purchase this plastic cover? Mine is missing and no one will work on my computer without it.

    jodieabc - 返信

    There is no point on going near the battery or logic board. I cut out these steps with no issue. It is precautionary but unnecessary.

    Jaime Leonard - 返信

    I agree. No point in removing the battery connection, as it’s one more thing that can break. Just be careful to shut down your machine before doing any work on it.

    Ron LaPedis -

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - 返信

    My new battery kit included a replacement for this part, so, no need to save the old one.

    Ralph Begleiter - 返信

  5. スパッジャーの平面側先端を使って、バッテリーコネクターをロジックボード上のソケットからまっすぐ持ち上げます。 コネクターのみ持ち上げるよう確認しながら作業を進めてください。ソケットには接触しないでください。ロジックボードに永久的なダメージを与えてしまうことがあります。
    • スパッジャーの平面側先端を使って、バッテリーコネクターをロジックボード上のソケットからまっすぐ持ち上げます。

    • コネクターのみ持ち上げるよう確認しながら作業を進めてください。ソケットには接触しないでください。ロジックボードに永久的なダメージを与えてしまうことがあります。

    I have a friends MacBook Pro that has some water damage that caused the MacBook not to be able to use battery power, but still work when plugged into A/C. Upon further inspection I can see visible corrosion on a few of the 9 cables going from the battery connector to that small circuit board. Is it possible to just replace that circuit board?

    jramsey21 - 返信

    I have the some problem. I was thinking to replace the whole battery but I am not it will solve the problem. Any suggestions?

    salvatorebarbera -

    Sometimes it can be enough to just clean the contacts without having to replace the entire board. Dosent work for complicated IC's like plcc type, where corrosion is underneath the chip. Here you will have to reheat and reapply the IC.

    andrehedegaard -

    Hi,have you find the solution for your battery? I also have same problem, run with plugs but it battery not supporting… as soon the plug of it goes off

    Jewel Rahman -

    Have either of you replaced the battery and/or circuit board to fix the MacBooks with the water damage ? I have the same problem with the MacBook working fine when connected to power but dying immediately when the power cord is removed.

    Steve - 返信

    Hi, Steve. I had the same problem: Macbook Pro 15 retina with coffee damage. And it worked fine when connected to power. I made it working after replacing the whole battery. It seems that circuit connected to the battery becomes disabled to prevent short circuit.

    Vadim Gribanov -

    When placing the battery connector back into the socket on the logic board, check that every part of connector is pressed down. You should hear a soft click when it's back in place.

    Ethan Tarquin - 返信

    Thanks for the comment. My MBP isn’t powering on after I walked through these steps, and I assume it is because the battery connector isn’t fully connected. (I can’t check yet since I borrowed the pentalobe screwdriver)

    Caleb Steinborn -

    +1

    I thought I made sure it was connected but when running the computer it only detected the battery but couldn’t power it. I had to run with power adapter. Also it didn’t charge. I guess some pins were connected but not all. To verify that all were connected I removed the plastic cover, placed it carefully completely flat, and then reattached the plastic cover. After that it worked!

    Jonas Ehrs -

    If I only want to replace the trackpad cable, then which steps should I skip? This step seems unnecessary

    Parth Gudhka - 返信

    Removing the battery connector took a bit of finagling. It wasn’t as easy as one would think. Be very careful when doing this as they warn to not damage it. Otherwise great instructions!!!!

    Peppon - 返信

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - 返信

    I have verified I have this battery, and I have a mid-2014 macbook retina. And I swear i do not see this battery connector. I didn’t take the cover off, per other comments that said it was an unnecessary risk. What the heck? will I not see the battery cable without taking of that cover?

    martha - 返信

    How can i post a photo of what I am seeing …I don’t see the battery connector! not like in photo above. maybe I have to remove that plastic cover although others recommended not doing that (see above).

    martha - 返信

    ooops nevermind..I see it now! tks . But..there is SO much gunk/dust under there (old, hand me down, used by my teen daughter while eating in bed no doubt!) . Should I attempt to clean? Beyond just blowing on it? Is compressed air safe? Or should I just leave it be? Assuming I don’t break it while replacing this battery I’d like not to break it otherwise! tks

    martha - 返信

  6. 修理作業中、アクシデントによりソケットがバッテリーコネクターに接続しないよう、折り曲げて邪魔にならない位置に移動させてください。
    • 修理作業中、アクシデントによりソケットがバッテリーコネクターに接続しないよう、折り曲げて邪魔にならない位置に移動させてください。

    If you miss or let this step for later like I did, the power left in the battery even though the computer is completely shut down, will screw up the I/O board cable like I did. I noticed this after I put all the pieces back, turn the computer on and surprise, no wifi hardware is detected. -.-

    sebasgaes - 返信

    Not sure I understand: did leaving the battery plugged in permanently broke the I/O board (or anything else)?

    Adrien Izzet -

    I put a small piece of blue painters tape on the battery connector contacts to prevent it from accidentally making a connection and shorting. This helped keep things a bit more protected.

    LaymanLab - 返信

    That’s a great idea!

    David Lilliebridge - 返信

    I used a small piece of paper to prevent the connector from connecting, no need to wrestle with even low-stick adhesive.

    dbrick - 返信

    I replaced both my L and R speakers on my MBP mid-2014 13” withOUT doing this step.

    Evan Shulman - 返信

    I agree that inserting a small paper above between the socket and the connector was useful. I used post-it-note, but kept the adhesive away from the socket.

    Ralph Begleiter - 返信

  7. 出入力ボードのケーブルブラケットのロジックボード先端に留められた2.1 mm T5トルクスネジを2本外します。 出入力ボードケーブルブラケットを取り出します。
    • 出入力ボードのケーブルブラケットのロジックボード先端に留められた2.1 mm T5トルクスネジを2本外します。

    • 出入力ボードケーブルブラケットを取り出します。

    Do you know where I can purchase the i/o board cable bracket?

    jodieabc - 返信

  8. スパッジャーの平面側先端を使って、ロジックボード上のソケットから出入力ボードコネクターをまっすぐ引き上げます。 出入力ボードケーブルのみこじ開けるようにご注意ください。ソケット自体には接触しないでください。ロジックボードにダメージを与えてしまうことになります。
    • スパッジャーの平面側先端を使って、ロジックボード上のソケットから出入力ボードコネクターをまっすぐ引き上げます。

    • 出入力ボードケーブルのみこじ開けるようにご注意ください。ソケット自体には接触しないでください。ロジックボードにダメージを与えてしまうことになります。

  9. 出入力ボードケーブルのロジックボード側先端を邪魔にならない位置に折り曲げます。 ケーブルにダメージが入らないように、ケーブルの出入力ボード先端のベントで折り曲げてください。
    • 出入力ボードケーブルのロジックボード側先端を邪魔にならない位置に折り曲げます。

    • ケーブルにダメージが入らないように、ケーブルの出入力ボード先端のベントで折り曲げてください。

  10. スパッジャーの先端をコネクター付近の右側スピーカーケーブル下に丁寧に差し込み、ロジックボードのソケットからこのケーブルを押し上げます。 スパッジャーの先端をコネクター付近の右側スピーカーケーブル下に丁寧に差し込み、ロジックボードのソケットからこのケーブルを押し上げます。
    • スパッジャーの先端をコネクター付近の右側スピーカーケーブル下に丁寧に差し込み、ロジックボードのソケットからこのケーブルを押し上げます。

    I have performed battery swap without disconnecting the speakers!

    Aleš Smokvina - 返信

  11. 上部ケースから右側スピーカーケーブルを取り外します。 上部ケースから右側スピーカーケーブルを取り外します。 上部ケースから右側スピーカーケーブルを取り外します。
    • 上部ケースから右側スピーカーケーブルを取り外します。

    I have successfully replaced battery without removing the speaker cables, as proposed by the comments in the next steps.

    Furthermore, in the steps after 22, where the battery is removed from the upper case, I have easily performed with a credit card and a drop of rubbing alcohol on it and finished in several minutes. Try it!

    kem - 返信

  12. 上部ケースに留められた右側スピーカーから次のネジを外します。
    • 上部ケースに留められた右側スピーカーから次のネジを外します。

    • 5.7 mm T5 トルクスネジー1本

    • 6.5 mm T5トルクスネジー1本

    • 3.8 mm T5トルクスネジー1本

    Make sure you replace these screws exactly where they came from, same with the other speak.

    Dustin Steward - 返信

  13. 右側のスピーカーをケーブルの先端から持ち上げて、ケースから外します。 右側のスピーカーをケーブルの先端から持ち上げて、ケースから外します。 右側のスピーカーをケーブルの先端から持ち上げて、ケースから外します。
    • 右側のスピーカーをケーブルの先端から持ち上げて、ケースから外します。

    When replacing with the new speaker, the new piece could have some blue strips on the cable. Remove them to let the adhesive do its job and attach the cable to the surroundings to avoid having it loose.

    Victor Alcantar - 返信

終わりに

デバイスを再組み立てする際は、このインストラクションを逆の順番に従って作業を進めてください。

23 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

Midori Doiさんは世界中で修理する私たちを助けてくれています! あなたも貢献してみませんか?
翻訳を始める ›

Andrew Optimus Goldheart

メンバー登録日: 2009年10月17日

434,174 ポイント

411のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

108 メンバー

10,008のガイドは作成済み

コメント1件

my Speaker tone … can i stitch it ?

Mr Jay - 返信

コメントを追加

統計データを表示:

過去 24時間: 20

過去 7 日: 139

過去 30 日: 661

今までの合計 17,755