メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

Use this guide to replace the LCD cable connected inside the hinge of your MacBook Pro Retina Display Assembly.

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm P5 Pentalobe screws

    • Eight 3.0 mm P5 Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    If don’t have one of those neat project mats, then you can use small pieces of flattened blu-tack to hold the screws. If you arrange them in the shape of your mac book cover, and put the screws down methodically, you can get a one-to-one mapping of the screws to the correct screw holes.

    Toby Thurston - 返信

    Or you can use an ice tray where you put the screws and the parts in separate bays in the same order as they come in the instructions.

    timofej.se -

    The colors of the circles marking the locations of the screws are reversed.

    Homer Hegedus - 返信

    On my model A1425 these were all 1.2mm P5 screws. They all looked the same to me.

    bigfish333 - 返信

    This is great! I used a small magnetic white board, and wrote on it to identify the parts as I went. This whole process, from the fast shipment to the great instructions to the complete, high quality, tool kit has been great. I’m typing this comment on my resurrected laptop. Thank you! Sue

    Susan Greer - 返信

  1. Wedge your fingers between the upper case and the lower case.
    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case.

    • Remove the lower case and set it aside.

  2. The lower case is connected to the upper case at the center, with two plastic clips. During reassembly, gently push down the center of the lower case to reattach the two plastic clips. During reassembly, gently push down the center of the lower case to reattach the two plastic clips.
    • The lower case is connected to the upper case at the center, with two plastic clips.

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

  3. Remove the plastic cover adhered to the battery contact board.
    • Remove the plastic cover adhered to the battery contact board.

    This plastic cover wasn’t included with the new battery so I placed the original one back in. Was it supposed to go back in? This detail wasn’t clear since the original cover didn’t fit exactly over the newer battery connector. Plus any stickiness of adhesive that may have been there was gone.

    arnolfo santoro - 返信

    Hi, any issues with you computer after a year? I didn’t put mine back in either…

    Kevin Burlinson -

    Kevin, I forgot to place mine back in! How is your laptop doing without it?

    Dominic Radcliffe - 返信

    My “on button” isn't working. I was wondering can I just disconnect the battery like this, and plug it in to turn it on? Which is shown possible on earlier models on YouTube.

    carsrcrap - 返信

    Is it ok if I did put the plastic cover back in?

    Sandy Lyon - 返信

  4. Remove the following screws securing the battery connector board to the logic board:
    • Remove the following screws securing the battery connector board to the logic board:

    • Two 2.8 mm T6 Torx screws

    • One 7.0 mm T6 Torx shouldered screw

    Top screw in this image was not a T6. I found that a T5 bit fit this one.

    Alex Grayson - 返信

    I can not put back top screw holding the plastic part. Help please

    Tatiana Garcia - 返信

    The colors of the circles marking the locations of the screws in the photo are reversed.

    Homer Hegedus - 返信

  5. Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board. Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board.
    • Use tweezers to remove the small plastic cover located near the bottom right of the battery connector board.

    Is adhered to screw beneath, so lift firmly and slowly.

    Andrew - 返信

  6. Remove the wide head 6.4 mm T6 Torx screw securing the battery connector to the logic board assembly.
    • Remove the wide head 6.4 mm T6 Torx screw securing the battery connector to the logic board assembly.

    I lost this screw! How important is it? Will it be okay with just the 3 previously removed screws?

    Gerardo Jimenez - 返信

    Check your speakers for the screws. The magnet for the speakers is strong enough to stick to them.

    Jeff M - 返信

  7. Carefully lift the battery connector board up off the logic board. It is recommended to bend the battery cables just slightly, to keep the board suspended up above the logic board and out of the way.
    • Carefully lift the battery connector board up off the logic board.

    • It is recommended to bend the battery cables just slightly, to keep the board suspended up above the logic board and out of the way.

    • Do not fold the board completely over, or crease the cables, as this may damage the battery.

  8. Grasp the Interposer with tweezers. An interposer is the name for an interface that links one electrical connection to another. In this repair, it is the board connecting the battery to logic board.
    • Grasp the Interposer with tweezers.

    • An interposer is the name for an interface that links one electrical connection to another. In this repair, it is the board connecting the battery to logic board.

    • Lift the Interposer off the logic board and remove it.

    • Removing this board will ensure that the battery remains disconnected throughout your repair, preventing your computer from accidentally powering on. It's also a good idea to take it out so it doesn't fall out unexpectedly.

    WHy to remove battery contact board? Replace can happen without it also, right.

    Behram Beldagli - 返信

    You don’t want to work on a live system as you could damage parts

    Dan -

    How can I remove interposer I m not able to remove it

    Raunak - 返信

    you must lift it absolutely vertically, or it fouls against the locator pin in the corner- you can easily get the impression that it won’t come over the end of this pin- almost like it’s rivetted in. it isn’t. get a good grip on it with the tweezers in the centre hole & one of the sides, & lift it STRAIGHT up.

    duncan rmi -

    What happens if the Battery Contact Board fails?

    racoon2956 - 返信

    Be extra careful when tightening down on the interposer. When I powered on upon completion, the battery was not connected. When I opened it back up, I saw that one of the little metal nubs holding the interposer in place had snapped off (the one on the side, not the corner). I was able to carefully tighten the wide head screw back in, watching the alignment, and the battery was successfully recognized. Hopefully the connection holds up.

    Doug Krieger - 返信

    So something similar happened to me. One the the metal alignment nubs snapped off, and when I went to screw down the interposer it started emitting a burning smell. Do you guys think I fried the board? There doesn’t look to be any visual damage but the computer wont turn on.

    Geremy C -

    Where can I buy a replacement interposer? I may have lost mine in the process of replacing the battery.

    juan.su - 返信

    I bought an interposer on amazon

    Kris K - 返信

    I think I snapped off the nub as well, and the battery is not recognized . Replacing the interposer did not help, or trying to align it right. will have to try to replace the battery next.

    Kris K - 返信

    I really dont understand why to unplug so many parts if the SSD can be easily removed without all this effort. its not even connected to the battery..

    Gabriel Beolchi - 返信

    I was reassembling and put the interposer back and when the battery contact board touched the interposer, there was a little spark. Should I be worried?

    Sandy Lyon - 返信

  9. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  10. Use the tip of a spudger to push the iSight camera cable connector straight away from its socket on the logic board. It is recommended to carefully push on both sides of the connector to "walk" it out of its socket.
    • Use the tip of a spudger to push the iSight camera cable connector straight away from its socket on the logic board.

    • It is recommended to carefully push on both sides of the connector to "walk" it out of its socket.

    This was the hardest part of the repair for me. The iSight cable was really lodged in its socket. "Walking" the connector as the guide suggests -- i.e. pushing on each side alternately at a 45 degree angle (with more force than I expected) -- eventually worked.

    Katherine Agnew - 返信

  11. Move the iSight camera cable aside.
    • Move the iSight camera cable aside.

    It is pretty much impossible to do this step before you do the next one as the airport cables are in the way.

    maccentric - 返信

  12. Use the flat end of a spudger to pry and disconnect the three antenna cable connectors from the AirPort board. The three cables are coded with black sleeves of different lengths. During reassembly: Connect the long-sleeved cable to the socket closest to the ports.
    • Use the flat end of a spudger to pry and disconnect the three antenna cable connectors from the AirPort board.

    • The three cables are coded with black sleeves of different lengths. During reassembly:

    • Connect the long-sleeved cable to the socket closest to the ports.

    • The short-sleeved cable connects next to the screw.

    • The remaining cable has no sleeve, and connects in the last empty socket, next to the fan.

    What does the J0, J1 and J2 connections represent on the Airport Card? I had an issue where the wifi and bluetooth went out and said "Not Available" so I replaced the I/O board and the airport card. The Wifi now works but Bluetooth is still showing not available. I wanted to know which connection meant what and to see if I could fix the issue. I have reseated the cables, deleted the Bluetooh.plist file and reset SMC, but bluetooth still appears as Not Available.

    jlhunter2008 - 返信

    The long-sleeved and short-sleeved antenna cables are switched compared to this guide, on my Macbook Pro A1425. Maybe note which order they are in on your machine, since apparently they differ. http://i.imgur.com/r9g9ZXS.jpg

    Will Bradley - 返信

    Be very careful with these, I wasn't and two of the cables detached from the connectors!!

    Felix Waller - 返信

    Likewise, the antenna connectors on my Macbook A1425 Late 2012 Retina were not in the order as described in this guide. From the fan side the connectors should be - no sleeve, long sleeve, short sleeve

    smurad - 返信

    As two other users have mentioned, the long-and short-sleeved cables for my late 2012/early 2013 A1425 were not in the order mentioned in the guide. If the laptop is positioned with fan in the upper left corner, the order (left to right) is short sleeve, long sleeve, no sleeve. If it is positioned as it is in the photo with the fan in the lower right, the order (left to right) is no sleeve, long sleeve, short sleeve.

    Katherine Agnew - 返信

    I also found my cables were not as described in the guide. They were as @kagnew described.

    Daniel Revier - 返信

    My airport cables on my model A1425 were also as @kagnew described, not as written in the guide.

    bigfish333 - 返信

  13. Move the antenna cables aside, clear of the AirPort board.
    • Move the antenna cables aside, clear of the AirPort board.

    The display assembly has a metal retaining clip attached to the airport cables. I didn’t notice how this was positioned during disassembly, and it wasn’t mentioned in the guide. When I was reassembling the device, I found that it fit perfectly over the Torx T8 screws holding the display to the case. Attaching it here holds the airport cables nicely in place and out of the way.

    https://imgur.com/a/HK8mnOA

    bigfish333 - 返信

  14. Grab the black pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer. Pull the display data cable straight out of its socket on the logic board. Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.
    • Grab the black pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.

    • Pull the display data cable straight out of its socket on the logic board.

    • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

  15. Use a pair of tweezers to lift the rubber hinge covers up off the right and left display hinges. Use a pair of tweezers to lift the rubber hinge covers up off the right and left display hinges.
    • Use a pair of tweezers to lift the rubber hinge covers up off the right and left display hinges.

  16. Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge brackets. Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge brackets.
    • Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge brackets.

    I ended up stripping one of these out and had to use a T6 and some delicate pressure to get it out. Be careful.

    The T6 and a lot of downward pressure ended up doing the trick for me. YMMV

    Daniel Revier - 返信

    This was a P5 screw not a T5 on my model A1425.

    bigfish333 - 返信

  17. Use a pair of tweezers to lift aluminum hinge brackets off the right and left display hinges. Use a pair of tweezers to lift aluminum hinge brackets off the right and left display hinges.
    • Use a pair of tweezers to lift aluminum hinge brackets off the right and left display hinges.

  18. Remove the four inner 5.3 mm T8 Torx screws (two on each side) securing the display to the upper case. Remove the four inner 5.3 mm T8 Torx screws (two on each side) securing the display to the upper case.
    • Remove the four inner 5.3 mm T8 Torx screws (two on each side) securing the display to the upper case.

    There is a retainer for the airport cables that goes beneath the left and center screws.

    maccentric - 返信

    My screws were covered with a thin tape, much like scotch tape. I used tweezers to remove it.

    Daniel Revier - 返信

  19. Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown. While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the upper display bracket.
    • Open the MacBook Pro approximately 110 degrees, and place it sideways on the table, as shown.

    • While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the upper display bracket.

    • Be sure to hold the display and upper case together with your left hand. Failure to do so may cause the freed display/upper case to fall, potentially damaging each component.

    • Remove the last remaining T8 Torx screw securing the display to the upper case.

  20. Grip both halves of the device, one in each hand. Gently push forward on the bottom half of the device to detach it from the display assembly. Carefully set each component aside, making sure to set down the lower half keyboard-side down.
    • Grip both halves of the device, one in each hand.

    • Gently push forward on the bottom half of the device to detach it from the display assembly.

    • Carefully set each component aside, making sure to set down the lower half keyboard-side down.

  21. With the display facing towards you and the plastic clutch cover down, grab the clutch cover and slide it all the way to the right, towards the hinge. Lift the plastic cover from the bottom and remove it from the display.
    • With the display facing towards you and the plastic clutch cover down, grab the clutch cover and slide it all the way to the right, towards the hinge.

    • Lift the plastic cover from the bottom and remove it from the display.

    Is there any tricky to remove this plastic, i can do it its stuck

    conradodav - 返信

    I was able to remove this plastic peace by sliding to the right, and then it came out. You need to apply some force in order to do this.

    Artem Umanets - 返信

    There’s a minor addition on how you do this. There are covers on both the ends of this clutch cover and they are connected like a hinge. For some models, it’s sliding this clutch cover to right and then you need to turn this clutch cover anti-clockwise and you’ll hear some clicking sounds affirming that the clutch cover is disconnected. Atleast this worked in my case :) .

    Rahul Kushwah - 返信

  22. Peel up the tape covering the cable connector.
    • Peel up the tape covering the cable connector.

  23. Remove the two screws securing the cable to the case:
    • Remove the two screws securing the cable to the case:

    • Two T8 Torx screws.

  24. Remove the six screws securing the antenna assembly in place:
    • Remove the six screws securing the antenna assembly in place:

    • Six PH00 Phillips screws.

    • Lift the antenna assembly to reveal the LCD cable connector underneath the left side.

    I used steps 21 to 25 for a MacBook Pro late-2013 (A1398) to replace the LCD cable - though there are 7 screws on the antenna assembly on that model. The other steps are similar, but MacBook Pro 15" Retina Display Late 2013のディスプレイアセンブリの交換 is more suitable for that model.

    Harvey Thompson - 返信

  25. Grab the metal bar securing the LCD cable connector in place and rotate it towards the bottom of the display.
    • Grab the metal bar securing the LCD cable connector in place and rotate it towards the bottom of the display.

    • Pull the LCD cable straight out of its socket on the display.

    • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the display.

終わりに

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

Jonah Aragon

メンバー登録日: 2018年08月05日

3,187 ポイント

4のガイドは作成済み

チーム

Experimax Coon Rapids Experimax Coon Rapids人のメンバー

Business

2 メンバー

6のガイドは作成済み

3 件のコメント

Hi,

Can anyone help me ? It might be possible that my MacBook Pro 13” early 2015 restarts by it self once in a few minutes because this cable is slightly damaged? It had before LCD problems and has been serviced. As I have noticed, when I touch the cable and move it a little bit, computer restarts immediately, so I thought this might be the restarting problem.

(I have to say that I have already tried other options : I have fresh reinstalled the operating system, so theres no software issue, I have repasted the processor, I have checked the cables connections). The only strange thing is that it doesn’t turn on with the battery disconnected…

Does anyone have any suggestion?

Thanks a lot!!

Ina - 返信

Are there instructions using the MacBook Pro (Retina, 15-inch, Early 2013)? The inside is completely different. Alas.

Jennifer Dibble Fanning - 返信

I'm getting this because the hing broke. The real problem is both hinges have broken. Seems like the other hinge is not possible to replace. Is that right? Will just this one side be enough to open with light use? My Mac is a early 2013 15inch pro. Model A1398

Stewart Lyon - 返信

コメントを追加

統計データを表示:

過去 24時間: 22

過去 7 日: 76

過去 30 日: 305

今までの合計 2,842