メインコンテンツにスキップ
  1. この手順は未翻訳です。 翻訳を手伝う。

    Unfold the antennas straight away from the device.
    • Unfold the antennas straight away from the device.

  2. この手順は未翻訳です。 翻訳を手伝う。

    Remove the black caps from the antennas by pulling them away from the device. Remove the black caps from the antennas by pulling them away from the device. Remove the black caps from the antennas by pulling them away from the device.
    • Remove the black caps from the antennas by pulling them away from the device.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Unscrew each of the antennas from the wireless device. Unscrew each of the antennas from the wireless device. Unscrew each of the antennas from the wireless device.
    • Unscrew each of the antennas from the wireless device.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Using a bit of force, remove the blue plastic case. Using a bit of force, remove the blue plastic case.
    • Using a bit of force, remove the blue plastic case.

  5. この手順は未翻訳です。 翻訳を手伝う。

    To remove the black casing that surrounds the green motherboard, slide the top half of the casing backwards. It only moves a very short distance. Pull the top piece upwards and away from the bottom to remove.
    • To remove the black casing that surrounds the green motherboard, slide the top half of the casing backwards. It only moves a very short distance.

    • Pull the top piece upwards and away from the bottom to remove.

  6. この手順は未翻訳です。 翻訳を手伝う。

    Locate the 2 M2.5x6mm screws that attach the motherboard to the back case. Remove the two screws from the motherboard as indicated with the Phillips head screwdriver.
    • Locate the 2 M2.5x6mm screws that attach the motherboard to the back case.

    • Remove the two screws from the motherboard as indicated with the Phillips head screwdriver.

  7. この手順は未翻訳です。 翻訳を手伝う。

    Once screws have been removed, slide the motherboard in the direction of its LED lights.
    • Once screws have been removed, slide the motherboard in the direction of its LED lights.

    • Lift motherboard up and away from the black lower casing.

  8. この手順は未翻訳です。 翻訳を手伝う。

    Obtain a desoldering wick (Desoldering Braid). Plug in soldering iron and allow to heat. For soldering information, refer to the iFixit soldering guide (はんだ付けとはんだ除去の作業ガイド).
    • Obtain a desoldering wick (Desoldering Braid). Plug in soldering iron and allow to heat. For soldering information, refer to the iFixit soldering guide (はんだ付けとはんだ除去の作業ガイド).

    • Make sure that the soldering iron is not resting on top of anything that would be damaged by the heat.

  9. この手順は未翻訳です。 翻訳を手伝う。

    Identify the functional component which will be removed. Turn the board over so that the pins holding the component in are exposed.
    • Identify the functional component which will be removed.

    • Turn the board over so that the pins holding the component in are exposed.

  10. この手順は未翻訳です。 翻訳を手伝う。

    Desolder each pin using the iFixit Soldering Guide (はんだ付けとはんだ除去の作業ガイド). Gently remove functional component for replacement.
ゴール

ある他の人がこのガイドを完成しました。

Nicole C

メンバー登録日: 2011年10月12日

102 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 17-7, Regan Fall 2011 Cal Poly, Team 17-7, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S17G7

4 メンバー

4のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 9

今までの合計 3,568