はじめに

As the projector heats up due to lamp use and processor heat, the fan speeds up to circulate cool air throughout the interior of the projector, and push hot air outside, so that the projector can continue to operate normally and not become damaged from overheating.

Place the projector on its back (buttons down) with the lens facing away from you. Remove the two 84mm screws in the upper left and right corners of the projector using the Phillips #2 screwdriver.
  • Place the projector on its back (buttons down) with the lens facing away from you.

  • Remove the two 84mm screws in the upper left and right corners of the projector using the Phillips #2 screwdriver.

  • Remove the remaining three 8.5mm screws using the Phillips #1 screwdriver.

コメントを追加する

Use the plastic opening tools to push down the clips holding the lamp cover in place, and remove it. There is no lamp assembly in the projector used in this guide, yours may appear different.
  • Use the plastic opening tools to push down the clips holding the lamp cover in place, and remove it.

  • There is no lamp assembly in the projector used in this guide, yours may appear different.

コメントを追加する

Remove the two 8.5mm rear screws holding the rear case plate to the projector using the Phillips #1 screwdriver. Pull the rear plate straight off and set it aside.
  • Remove the two 8.5mm rear screws holding the rear case plate to the projector using the Phillips #1 screwdriver.

  • Pull the rear plate straight off and set it aside.

コメントを追加する

Flip the projector over and turn around so that the lens faces you. Twist the gray zoom adjustment ring clockwise and extend the lens all the way out, and then slide the zoom adjustment ring all the way towards the end of the lens as far as it will go. Slide the front case plate towards the loosened zoom adjustment ring, until the top plate of the projector is freed from underneath the lip of the front case plate.
  • Flip the projector over and turn around so that the lens faces you.

  • Twist the gray zoom adjustment ring clockwise and extend the lens all the way out, and then slide the zoom adjustment ring all the way towards the end of the lens as far as it will go.

  • Slide the front case plate towards the loosened zoom adjustment ring, until the top plate of the projector is freed from underneath the lip of the front case plate.

  • The front case plate will not come all the way off due to the zoom adjustment ring obstructing it. It will merely slide forward a bit.

コメントを追加する

Lift away the top case plate and set it aside. Lift away the top case plate and set it aside.
  • Lift away the top case plate and set it aside.

コメントを追加する

Remove the four T10 Torx 8.5 mm screws holding the DLP board in place.
  • Remove the four T10 Torx 8.5 mm screws holding the DLP board in place.

コメントを追加する

Unplug the small ribbon cable attaching the DLP board to the motherboard.
  • Unplug the small ribbon cable attaching the DLP board to the motherboard.

コメントを追加する

Remove Secondary Fan Cable
  • Remove Secondary Fan Cable

コメントを追加する

Detach the DLP board from where it is connected to the motherboard by a large 100 pin connector. Pry up gently while wiggling from left to right if needed.
  • Detach the DLP board from where it is connected to the motherboard by a large 100 pin connector.

    • Pry up gently while wiggling from left to right if needed.

  • The ribbon cable on the other side of the board could break if pulled too hard.

コメントを追加する

Remove the 2 remaining T10 Torx 8mm screws securing the motherboard to the power supply.
  • Remove the 2 remaining T10 Torx 8mm screws securing the motherboard to the power supply.

コメントを追加する

Remove the speaker power cable.
  • Remove the speaker power cable.

コメントを追加する

Remove DLP Power Cable.
  • Remove DLP Power Cable.

コメントを追加する

Pry out the DLP support piece by gently wiggling it side to side while applying a steady pull. It will slide out. Pry out the DLP support piece by gently wiggling it side to side while applying a steady pull. It will slide out.
  • Pry out the DLP support piece by gently wiggling it side to side while applying a steady pull. It will slide out.

コメントを追加する

Remove the black plastic retaining clip reinforcing the large ribbon cable connector by prying it from the left edge. Gently pry the large ribbon cable connector from the DLP board, and remove the board.
  • Remove the black plastic retaining clip reinforcing the large ribbon cable connector by prying it from the left edge.

  • Gently pry the large ribbon cable connector from the DLP board, and remove the board.

  • Using too much force could damage the connector.

コメントを追加する

Remove the two 1/4" screws using the nut driver. The second screw is located behind the right side of the 100 pin connector. Gently pry up the motherboard from the connector on top of the power supply.
  • Remove the two 1/4" screws using the nut driver.

    • The second screw is located behind the right side of the 100 pin connector.

  • Gently pry up the motherboard from the connector on top of the power supply.

コメントを追加する

Disconnect the lamp power supply cables from the top of the lamp housing, by gently pulling the two wires in opposite directions. Disconnect the lamp power supply cables from the top of the lamp housing, by gently pulling the two wires in opposite directions.
  • Disconnect the lamp power supply cables from the top of the lamp housing, by gently pulling the two wires in opposite directions.

コメントを追加する

Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out. Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out. Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out.
  • Use your thumbs to pry the sides of the external shell away from the power supply so it can be lifted out.

コメントを追加する

Detach the main fan power cable from the power supply.
  • Detach the main fan power cable from the power supply.

コメントを追加する

Use the needle nose pliers to pull out the grommets securing the main fan to its housing. To replace grommets, pull the center pins from their housing, and slip the exteriors of the grommets back into their holes in the fan housing, then push the centers in to secure them in place. To replace grommets, pull the center pins from their housing, and slip the exteriors of the grommets back into their holes in the fan housing, then push the centers in to secure them in place.
  • Use the needle nose pliers to pull out the grommets securing the main fan to its housing.

  • To replace grommets, pull the center pins from their housing, and slip the exteriors of the grommets back into their holes in the fan housing, then push the centers in to secure them in place.

コメントを追加する

Remove the fan from its housing.
  • Remove the fan from its housing.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Andrew Kennedy

メンバー登録日: 2013年01月29日

120 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 20-3, Maness Winter 2013 Cal Poly, Team 20-3, Maness Winter 2013人のメンバー

CPSU-MANESS-W13S20G3

4 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 4

過去 7 日: 7

過去 30 日: 15

今までの合計 1,196