はじめに

Like all graphics cards, the Radeon X1900 XTX occasionally needs to be opened up and cleaned in order to function properlly.

Once you remove the heat sink, you'll need to reapply thermal paste to the GPU die. Follow our Applying Thermal Paste Guide for detailed directions.

Start by removing the card from the PC if you haven't already. Start by removing the card from the PC if you haven't already.
  • Start by removing the card from the PC if you haven't already.

コメントを追加する

The fan's power cable is located towards the bottom-left of the card. Disconnect the cable from the card. The cable and its connector on the X1900 are fragile.  Be careful, and try not to use excessive force when removing it.
  • The fan's power cable is located towards the bottom-left of the card.

  • Disconnect the cable from the card.

  • The cable and its connector on the X1900 are fragile. Be careful, and try not to use excessive force when removing it.

コメントを追加する

Removing the heatsink from the card: The clamp is held on by four small Phillips screws.  Remove them, then the clamp. Remove the four phillips screws surrounding the clamp.
  • Removing the heatsink from the card:

  • The clamp is held on by four small Phillips screws. Remove them, then the clamp.

  • Remove the four phillips screws surrounding the clamp.

コメントを追加する

Seperate the heatsink and the card.
  • Seperate the heatsink and the card.

if you're doing this on a Mac, you have to take out the two small screws on the dvi connection end and loosen the dvi connection nuts so the heatsink will separate.

Matt Kennedy - 返信

Replacing Thermal Paste: Using a Q-tip/cotton swab and rubbing alcohol, clean the copper plate that protrudes from the bottom of the heatsink.
  • Replacing Thermal Paste:

  • Using a Q-tip/cotton swab and rubbing alcohol, clean the copper plate that protrudes from the bottom of the heatsink.

コメントを追加する

Removing the heatsink's plastic cover: Remove these Phillips screws.
  • Removing the heatsink's plastic cover:

  • Remove these Phillips screws.

  • Seperate the plastic cover from the metal heat sink.

コメントを追加する

Cleaning dust out of the heat sink: Using a cotton swab/q-tip, clean the edges of the heat sink.  You can also use canned air if available.
  • Cleaning dust out of the heat sink:

  • Using a cotton swab/q-tip, clean the edges of the heat sink. You can also use canned air if available.

コメントを追加する

Using the same method that you used to clean the copper plate, clean the surface of the GPU die. Using the same method that you used to clean the copper plate, clean the surface of the GPU die.
  • Using the same method that you used to clean the copper plate, clean the surface of the GPU die.

コメントを追加する

  • Re-Applying Thermal Paste:

  • Apply a small glob of thermal paste to the corner of the die, (I recommend using Arctic Silver 5) and use an index card to spread a thin, even layer of it over the surface of the chip.

  • For more detailed directions, follow our Applying Thermal Paste Guide.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

11 の人々がこのガイドを完成させました。

Chris Green

メンバー登録日: 2009年10月11日

31,975 ポイント

47のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

277 メンバー

724のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 3

過去 7 日: 6

過去 30 日: 25

今までの合計 11,036