修理を始めるには コミュニティ ストア

GravityLight LED Replacement

はじめに

If the white LED light will not turn on, then you will have to open up the device and replace the LED.

必要な工具と部品

  1. GravityLight LED Replacement, Removing the Front Panel: 手順 1、 2の画像 1 GravityLight LED Replacement, Removing the Front Panel: 手順 1、 2の画像 2

    • Flip the GravityLight on its back and place it on a sturdy surface.

    • Unscrew the three 2cm Phillips #00 screws on the back of the GravityLight’s body.

    翻訳

  2. GravityLight LED Replacement, Opening the Device Housing: 手順 2、 1の画像 1

    • Some of the internal pieces may loosen or fall out during disassembly.

    • Firmly grasp both parts of the GravityLight body and pull them apart.

    翻訳

  3. GravityLight LED Replacement, Removing the Back Panel Screws: 手順 3、 1の画像 1

    • Place the back panel, the larger of the two pieces, on a sturdy surface with its back down.

    • Unscrew the two 2cm Phillips 00 screws on the inside of the back panel.

    翻訳

  4. GravityLight LED Replacement, Removing the LED Housing: 手順 4、 2の画像 1 GravityLight LED Replacement, Removing the LED Housing: 手順 4、 2の画像 2

    • Hold the LED housing in your hand, but do not separate it too far otherwise you will tear the wires.

    • Lift the LED housing away from the back panel.

    翻訳

  6. GravityLight LED Replacement, Remove the White Gear from the LED Housing: 手順 5、 2の画像 1 GravityLight LED Replacement, Remove the White Gear from the LED Housing: 手順 5、 2の画像 2

    • Grab the outside of the large, white gear in the LED housing and pull the gear out of the housing.

    翻訳

  7. GravityLight LED Replacement, Position the LED Housing: 手順 6、 1の画像 1

    • Set the LED housing flat on a sturdy surface so that the back of the LED and the wires are exposed.

    翻訳

  8. GravityLight LED Replacement, Cut the Wires: 手順 7、 1の画像 1

    • Place the GravityLight's back panel aside.

    • Use the Flush Wire Cutter to cut both the purple wire and the red wire that connect to the LED.

    翻訳

  9. GravityLight LED Replacement, Bend the LED Leads: 手順 8、 1の画像 1

    • Take tweezers and bend the leads (the silver wires coming out of the bulb) so that the leads are straight.

    • The straight leads will make the LED easier to take out.

    翻訳

  10. GravityLight LED Replacement, Remove the LED: 手順 9、 1の画像 1

    • Flip the LED housing over.

    • Pull the LED out with tweezers.

    翻訳

  11. GravityLight LED Replacement, Soldering the New LED: 手順 10、 1の画像 1

    • For reassembly: Flip the LED housing back over.

    • Put the new LED in its spot. Solder the red wire and the purple wire back onto the new leads.

    • Make sure that you pair each wire to the correct lead. If the LED still does not light, switch the wires on the leads.

    • For information on how to solder look here: はんだ付けとはんだ除去の作業ガイド

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

2人の作成者と共同で作成されました。

Brian Gouldsberry

メンバー登録日: 09/26/14

201 ポイント

2のガイドは作成済み

バッジ: 4

+1 以上のバッジ

チーム

Cal Poly, Team 12-2, Forte Fall 2014 Cal Poly, Team 12-2, Forte Fall 2014人のメンバー

CPSU-FORTE-F14S12G2

5 メンバー

7のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 613