Skip to main content

はじめに

Use this guide to replace the plastic button covers and the rubber button contacts on any DualShock 3 controller.

パーツ

パーツは指定されていません。

  1. Remove the five 7.2 mm Phillips screws securing the rear cover to the controller.
    • Remove the five 7.2 mm Phillips screws securing the rear cover to the controller.

  2. Press on the rear cover between the analog sticks and slightly lift the lower edge of it away from the rest of the controller.
    • Press on the rear cover between the analog sticks and slightly lift the lower edge of it away from the rest of the controller.

  3. Push the rear cover slightly toward the top edge of the controller to clear the front edge of the #2 triggers. Pull the rear cover away from the rest of the controller, being careful not to pop off the #2 triggers.
    • Push the rear cover slightly toward the top edge of the controller to clear the front edge of the #2 triggers.

    • Pull the rear cover away from the rest of the controller, being careful not to pop off the #2 triggers.

    • If you happen to accidentally pop off the trigger buttons, we have a trigger button guide to reattach them.

  4. Lift the battery off the motherboard for enough clearance to access the battery connector.
    • Lift the battery off the motherboard for enough clearance to access the battery connector.

  5. MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now

    MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now
  6. Carefully pull the battery connector away from its socket on the motherboard.
    • Carefully pull the battery connector away from its socket on the motherboard.

    • It may be helpful to use a pair of tweezers or pliers to grab the battery connector when you disconnect it for the first time. Only pull on the connector. Do not try to remove by pulling on the red and black wires.

  7. Remove the single 7.2 mm Phillips screw securing the motherboard to the front cover.
    • Remove the single 7.2 mm Phillips screw securing the motherboard to the front cover.

  8. Slide the trigger button retainers slightly away from the front cover. Remove the #1 button on both sides. Remove the #1 button on both sides.
    • Slide the trigger button retainers slightly away from the front cover.

    • Remove the #1 button on both sides.

  9. Pull the vibration motor retainers away from the front cover to dislodge the motherboard assembly. Pull the vibration motor retainers away from the front cover to dislodge the motherboard assembly.
    • Pull the vibration motor retainers away from the front cover to dislodge the motherboard assembly.

  10. Remove the motherboard assembly from the front cover.
    • Remove the motherboard assembly from the front cover.

    • When removing the motherboard assembly, try not to tilt the front cover upside down as the buttons and their covers may fall out.

  11. Lift the rubber button contacts off the front controller cover to access the plastic button covers. Lift any damaged plastic button covers out of the controller cover.
    • Lift the rubber button contacts off the front controller cover to access the plastic button covers.

    • Lift any damaged plastic button covers out of the controller cover.

  12. The D-pad has a three-armed plastic piece that must be installed as shown before installing the rubber button pad for it to work properly.
    • The D-pad has a three-armed plastic piece that must be installed as shown before installing the rubber button pad for it to work properly.

まとめ

To reassemble your device, follow these instructions in reverse order.

66 の人々がこのガイドを完成させました。

Andrew Bookholt

515,543 ポイント

618のガイドは作成済み

My Dualshock 3 didn't have the three armed plastic piece on the D-pad. Mine's a red one, relatively recent. My controller also had the problem where it would randomly send button press events when using the L-stick. I traced the problem to the ribbon connector between the board and the contacts, which was very dirty. I cleaned the contacts and put the controller back together with an additional rubber shim between the back cover and the battery, which got rid of the creakiness of the somewhat loose-fitting case. Works great now.

Kevin - 返信

How do you clean the contacts? Is there a special way?

yeshuabendavid -

Thanks. ^^ Tightened screws after opening it and this kind of problem got solved.

Janne K - 返信

Are these instructions the same for the dual-shock 2?

Larry Howard - 返信

TNX-could not really figure out where the 3-armed plastic should fit in but tnx to step 11 i know-now im going to dismantle my controller again.

Kristian Brandström - 返信

コメントを追加する

統計データを表示:

過去 24時間: 14

過去 7 日: 131

過去 30 日: 600

今までの合計 123,951