はじめに

Replace or upgrade your Phantom motors. This guide requires soldering.

Each motor's direction is determined by the order of its leads on the ESC, so when you're replacing, be sure to match the original order. Motors on opposite arms will have the same direction, so check the other arm for reference.

If you're ordering a replacement, be sure to get the right thread direction for your motor, or the propellor collet will loosen during flight.

パーツ

Press down on battery door release tab to flip the battery door open. Press down on battery door release tab to flip the battery door open. Press down on battery door release tab to flip the battery door open.
  • Press down on battery door release tab to flip the battery door open.

コメントを追加する

Pull out the battery pack. Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints. Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints.
  • Pull out the battery pack.

  • Avoid pulling on the battery wires, excess stress may break the wires, damage the power connectors, or crack the internal solder joints.

コメントを追加する

Pull the two halves of the XT60 power connector apart. It's a tight fit, so be careful not to hit your drone or yank on the cables when it releases!
  • Pull the two halves of the XT60 power connector apart.

    • It's a tight fit, so be careful not to hit your drone or yank on the cables when it releases!

コメントを追加する

Silver-topped propeller collets unscrew counter-clockwise Black-topped propeller collets unscrew clockwise
  • Silver-topped propeller collets unscrew counter-clockwise

  • Black-topped propeller collets unscrew clockwise

コメントを追加する

For propellors with silver collets: Use a 12 mm wrench or socket to loosen silver collets in the counter-clockwise direction. Once free, unscrew and remove the collet. Once free, unscrew and remove the collet.
  • For propellors with silver collets: Use a 12 mm wrench or socket to loosen silver collets in the counter-clockwise direction.

  • Once free, unscrew and remove the collet.

コメントを追加する

For propellors with black collets: Use a 12 mm wrench or socket to loosen black collets in the clockwise direction. Once free, unscrew and remove the collet. Once free, unscrew and remove the collet.
  • For propellors with black collets: Use a 12 mm wrench or socket to loosen black collets in the clockwise direction.

  • Once free, unscrew and remove the collet.

コメントを追加する

Gently press down the motor shaft and lift the propeller up to remove it. Gently press down the motor shaft and lift the propeller up to remove it. Gently press down the motor shaft and lift the propeller up to remove it.
  • Gently press down the motor shaft and lift the propeller up to remove it.

コメントを追加する

After removing all four propellors, flip the drone over. Remove the following screws from the underside of the drone: Twelve 2.0 mm hex screws
  • After removing all four propellors, flip the drone over.

  • Remove the following screws from the underside of the drone:

    • Twelve 2.0 mm hex screws

    • Four Phillips #0 screws

コメントを追加する

Loosen the cable from the plastic landing gear. Unplug the magnetometer molex connector. Unplug the magnetometer molex connector.
  • Loosen the cable from the plastic landing gear.

  • Unplug the magnetometer molex connector.

コメントを追加する

Lift up on the top portion of the shell and set it on its side. Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables. Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables.
  • Lift up on the top portion of the shell and set it on its side.

  • Do not attempt to fully remove the case. The GPS and Magnetometer cables connect the top shell to the rest of the Phantom, be careful not to stress or break these cables.

コメントを追加する

Lift the GPS cable molex connector up out of its socket on the main board. Lift the GPS cable molex connector up out of its socket on the main board.
  • Lift the GPS cable molex connector up out of its socket on the main board.

On the Phantom FCP40 (essentially a Phantom 1), the GPS cable connects directly to the Naza controller box, not to the board as shown here. Also the compass (magnetometer) is connected to the main board, not the GPS unit in the top shell, so you don't need to remove it to remove the top shell.

Marcus Bointon - 返信

Gently pull the slack of the magnetometer cable through the case bottom shell. The case top shell should now have enough slack to work on the interior of the Phantom. The case top shell should now have enough slack to work on the interior of the Phantom.
  • Gently pull the slack of the magnetometer cable through the case bottom shell.

  • The case top shell should now have enough slack to work on the interior of the Phantom.

コメントを追加する

Desolder all three motors wires from the speed controller board. Follow our soldering guide to learn how, or just to brush-up on your skills.
  • Desolder all three motors wires from the speed controller board.

    • Follow our soldering guide to learn how, or just to brush-up on your skills.

  • Be careful not to melt the plastic case bottom shell with your soldering iron or damage any electronic components.

  • When you're reassembling, solder the motor leads back in their original order. This may be different from the picture. Motors on arms across from each other have the same color order, so check the opposite arm for reference.

コメントを追加する

Unscrew the four 2 mm motor hex bolts from the case bottom shell.
  • Unscrew the four 2 mm motor hex bolts from the case bottom shell.

コメントを追加する

Remove the motor from the Phantom. Remove the motor from the Phantom.
  • Remove the motor from the Phantom.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

David Hoyt

メンバー登録日: 2010年04月09日

3,599 ポイント

44のガイドは作成済み

チーム

Cal Poly, Team 25-89, Amido Spring 2010 Cal Poly, Team 25-89, Amido Spring 2010人のメンバー

CPSU-AMIDO-S10S25G89

4 メンバー

52のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 5

過去 7 日: 27

過去 30 日: 156

今までの合計 15,903