メインコンテンツにスキップ

はじめに

For sticky cold/hold buttons, you may only need to clean the button. This guide will show you how to fully remove and replace the button.

Note: This guide requires soldering skills. If you don't know how to solder or want to brush up on your skills check out this handy tutorial.

パーツ

パーツは指定されていません。

  1. Caution: Unplug the hair dryer before attempting this guide. Leaving the device plugged in may result in electrocution and damage to the device.
    • Caution: Unplug the hair dryer before attempting this guide. Leaving the device plugged in may result in electrocution and damage to the device.

    • Hold the hair dryer by the handle so that the back panel faces up.

  2. Remove the two 15.875 mm Phillips #2 screws from the back panel. Remove the two 15.875 mm Phillips #2 screws from the back panel.
    • Remove the two 15.875 mm Phillips #2 screws from the back panel.

  3. Starting from where the cord attaches to the handle, pull apart the two plastic panels. Continue separating the back panel, working along the seam. With moderate force, completely remove the back panel from the hair dryer.
    • Starting from where the cord attaches to the handle, pull apart the two plastic panels.

    • Continue separating the back panel, working along the seam.

    • With moderate force, completely remove the back panel from the hair dryer.

  4. Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る

    Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る
  5. Hold the hair dryer by the nozzle so that the handle points to the left. Remove the two 1-inch Phillips #2 screws from the back of the fan motor.
    • Hold the hair dryer by the nozzle so that the handle points to the left.

    • Remove the two 1-inch Phillips #2 screws from the back of the fan motor.

  6. Caution: If you recently used the hair dryer, wait at least 10 minutes before attempting this step. The heating element may still be very hot and can cause serious burns. Pull on the back of the fan motor to gently lift the motor out of the hair dryer. Lift the attached electrical wiring and heat shield completely out of the hair dryer.
    • Caution: If you recently used the hair dryer, wait at least 10 minutes before attempting this step. The heating element may still be very hot and can cause serious burns.

    • Pull on the back of the fan motor to gently lift the motor out of the hair dryer.

    • Lift the attached electrical wiring and heat shield completely out of the hair dryer.

  7. Caution: Do not attempt to open or tamper with the capacitor. You may suffer severe electrical shocks.
    • Caution: Do not attempt to open or tamper with the capacitor. You may suffer severe electrical shocks.

    • Hold the electrical switches so that the wires are facing upwards.

  8. Focus on the middle of the three buttons.
    • Focus on the middle of the three buttons.

    • Desolder the button at the circled locations.

    • To reattach the new button, resolder at the same points. Be sure the wires connect to the correct locations.

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Timothy Lo

メンバー登録日: 2014年04月22日

917 ポイント

7のガイドは作成済み

チーム

Cal Poly, Team 10-58, Amido Spring 2014 Cal Poly, Team 10-58, Amido Spring 2014人のメンバー

CPSU-AMIDO-S14S10G58

4 メンバー

7のガイドは作成済み

so where do you buy parts???

akatser1 - 返信

That's not a capacitor, that's an ion generator like this one https://www.goldmine-elec-products.com/p...

Shannon Carey - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 14

今までの合計 2,967