メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Canon Pixma MP480 Data Port Replacement

作成者： Steven MacLean (そして 4 人のその他投稿者)
  • コメント: 0
  • お気に入り: 4

難易度

難しい

手順

29

所要時間

45分 - 1時間

セクション

4

フラグ

5

Needs More Images

多くの画像が必要

幾つかの画像があればこのガイドの手順がより明確になるでしょう。

Action Shots

アクションショット

アクションヒーローになりましょう！このガイドはある特定の動作をどのように行なうのか、より詳細な画像が必要です。

Inconsistent Images

一貫性のない画像

このガイドの画像を必要条件ガイドとより一致するように変更するとさらに素晴らしくなります。

Confusing Text

不明瞭なテキスト

このガイドのテキストの数カ所が混乱し、重複しトピックから外れています。編集してより明確にしてください！

Markup Mishap

間違いの指摘

このガイドは最適な校正が必要です。校正の注釈を付けたり訂正することにご協力ください。

はじめに

Please complete the dis-assembly guide before attempting to install new data ports, as it is a prerequisite.

Use this guide to replace a broken data port to get your USB and card readers back.

ツール

これらのツールを購入する

パーツ

  1. Remove the following two Phillips screws: Two 7.85 mm Phillips #1 screws

    • Remove the following two Phillips screws:

    • Two 7.85 mm Phillips #1 screws

    編集

  2. Pull the back cover off by lifting up on the cover.

    • Pull the back cover off by lifting up on the cover.

    • You may need to pull firmly as it requires quite a bit of force.

    編集

  3. Open the front tray.

    • Open the front tray.

    編集

  4. Lift the scanner compartment.

    • Lift the scanner compartment.

    編集

  5. After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.

    • After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.

    編集

  6. Push the blue lever back while twisting it clockwise in order to remove the lever from its slot. After removing the lever, close the scanner compartment and the scanner cover.

    • Push the blue lever back while twisting it clockwise in order to remove the lever from its slot.

    • After removing the lever, close the scanner compartment and the scanner cover.

    編集

  7. Use the plastic opening tool to pry open the side cover. Use the plastic opening tool to pry open the side cover.

    • Use the plastic opening tool to pry open the side cover.

    編集

  8. Flip the printer so that you are facing the underside. Use the plastic opening tool to remove the corner of the side panel from the pin.

    • Flip the printer so that you are facing the underside.

    • Use the plastic opening tool to remove the corner of the side panel from the pin.

    • Plastic pin.

    編集

  9. Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer. Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.

    • Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.

    編集

  10. Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture). Pry around the front and side edges for the easiest removal.

    • Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture).

    • Pry around the front and side edges for the easiest removal.

    編集

  11. Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る

    Android 修理キット

    A new screen or battery is one kit away.

    ショップを見る

  12. After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.

    • After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.

    編集

  13. Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.

    • Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.

    編集

  14. Locate the buttons on the printer.

    • Locate the buttons on the printer.

    編集

  15. Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.

    • Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.

    編集

  16. Remove the following five Philips screws: Five 7.65 mm Philips #1 screws

    • Remove the following five Philips screws:

    • Five 7.65 mm Philips #1 screws

    編集

  17. Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture. Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.

    • Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.

    編集

  18. Remove the two screws using the Phillips #1 screwdriver. Two 7.8 mm Phillips #1 screws

    • Remove the two screws using the Phillips #1 screwdriver.

    • Two 7.8 mm Phillips #1 screws

    編集

  19. Gently pull the LCD screen up to remove it from its fixture.

    • Gently pull the LCD screen up to remove it from its fixture.

    編集

  20. Use the plastic opening tool to pry off the plastic button assembly.

    • Use the plastic opening tool to pry off the plastic button assembly.

    編集

  21. Gently pull the plastic button assembly up to remove it.

    • Gently pull the plastic button assembly up to remove it.

    • The plastic button assembly has a ribbon cable connected on the bottom, so make sure to be careful pulling it.

    編集

  22. Remove the ribbon cable connected to the backside of the plastic button assembly.

    • Remove the ribbon cable connected to the backside of the plastic button assembly.

    編集

  23. Remove the seven screws using the Phillips #1 screwdriver. Seven 8.7 mm Phillips #1 screws

    • Remove the seven screws using the Phillips #1 screwdriver.

    • Seven 8.7 mm Phillips #1 screws

    編集

  24. Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly.

    • Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly.

    • Gently lift the spring and pull the board out of its plastic button assembly.

    編集

  25. Remove the buttons from the plastic button assembly.

    • Remove the buttons from the plastic button assembly.

    • Buttons

    編集

  26. Remove the screw using the Phillips #1 screwdriver. 7.5 mm Phillips #1 screw

    • Remove the screw using the Phillips #1 screwdriver.

    • 7.5 mm Phillips #1 screw

    編集

  27. Remove the five screws using the Phillips #1 screwdriver. Five 3.5 mm Phillips #1 screws

    • Remove the five screws using the Phillips #1 screwdriver.

    • Five 3.5 mm Phillips #1 screws

    編集

  28. Remove the small plastic clip using the spudger.

    • Remove the small plastic clip using the spudger.

    • Small plastic clip

    編集

  29. Pull plastic inserts out of the holes in the top and bottom.

    • Pull plastic inserts out of the holes in the top and bottom.

    • Top and bottom plastic inserts

    編集

  30. Completely remove the board from the printer by pulling the board towards the back of the printer.

    • Completely remove the board from the printer by pulling the board towards the back of the printer.

    • This requires effort and time as the board comes out little by little.

    編集
まとめ

To reassemble your device, follow these instructions in reverse order.

作成者

4他の投稿者と一緒に

Steven MacLean

メンバー登録日: 2013年01月14日

74 ポイント

2のガイドは作成済み

バッジ: 6

+3 個以上のバッジ

チーム

Cal Poly, Team 19-41, Regan Winter 2013 Cal Poly, Team 19-41, Regan Winter 2013人のメンバー

CPSU-REGAN-W13S19G41

4 メンバー

6のガイドは作成済み

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 7

今までの合計 1,608