メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

Use this guide to remove the front speaker panel in your device. You’ll need to know how to solder to fully replace the speaker panel in your Braven BRV-X. The How to Solder and Desolder Connections guide may help you with this guide.

  1. Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.
    • Remove four 1.1 cm outer screws in the outer shell using the Phillips #00 screwdriver.

  2. Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.
    • Remove four 1.3 cm inner screws in the outer shell using the 1.5mm Hex screwdriver.

  3. Gently remove the outer shell.
    • Gently remove the outer shell.

  4. Cut adhesive tape on both sides. Cut adhesive tape on both sides.
    • Cut adhesive tape on both sides.

  5. Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver. Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.
    • Remove eighteen 0.9cm screws in the inner shell using the Phillips #00 screwdriver.

  6. Pry open the glued inner shell using a spudger around all sides of the shell. Don't use too much pressure as that could cause damage to the plastic. Don't use too much pressure as that could cause damage to the plastic.
    • Pry open the glued inner shell using a spudger around all sides of the shell.

    • Don't use too much pressure as that could cause damage to the plastic.

  7. Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver. Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.
    • Remove ten 0.7 cm screws in the front plate using the 1.5 mm Hex screwdriver.

  8. Use a spudger to open the front speaker plate. Use a spudger to open the front speaker plate.
    • Use a spudger to open the front speaker plate.

  9. Remove three 1.0 cm screws from the battery unit.
    • Remove three 1.0 cm screws from the battery unit.

    • It is recommended (but not required) to remove the battery.

  10. Disconnect the ribbon cable attached the main board. Disconnect the ribbon cable attached the main board.
    • Disconnect the ribbon cable attached the main board.

  11. Pry open the second plate holding in the speaker using a spudger around all sides. It is recommended to use a spudger to remove the heavily glued areas between the plates before prying. Don't use too much pressure as that could cause damage to the plastic.
    • Pry open the second plate holding in the speaker using a spudger around all sides.

    • It is recommended to use a spudger to remove the heavily glued areas between the plates before prying.

    • Don't use too much pressure as that could cause damage to the plastic.

  12. Cut the 20 gauge wires attached to the front IR sensor and two speaker wires. Leave enough length on the wire to work with it afterwards. Cut the 22 gauge wire attached in the corner.
    • Cut the 20 gauge wires attached to the front IR sensor and two speaker wires.

    • Leave enough length on the wire to work with it afterwards.

    • Cut the 22 gauge wire attached in the corner.

    • Solder the new speaker plate during reassembly.

    • To properly solder and desolder connections, visit the How to Solder and Desolder Connections guide.

終わりに

To reassemble your device, follow these instructions in reverse order.

Trey Peterson

メンバー登録日: 2019年04月01日

301 ポイント

2のガイドは作成済み

チーム

IUPUI, Team S1-G5, Harley Spring 2019 IUPUI, Team S1-G5, Harley Spring 2019人のメンバー

IUPUI-HARLEY-S19S1G5

3 メンバー

2のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 127