Black and Decker LDX 120C Light Replacement - iFixit 修理ガイド

はじめに

If the light in the drill is not glowing upon use, then this guide will show a step by step process on how to replace the light bulb for the drill.

必要な工具と部品

手順1 Outer Case

Black and Decker LDX 120C Light Replacement, Outer Case: 手順 1、 1の画像 1

For this guide we will need to use a 1.0 mm phillips #1 screw.
There are a total of thirteen screws that need to be removed in order to open the drill and access the interior components.

手順2

Black and Decker LDX 120C Light Replacement: 手順 2、 1の画像 1

Remove the four screws on the back top side of the drill.

手順3

Black and Decker LDX 120C Light Replacement: 手順 3、 1の画像 1

Remove the four screws that connect the chuck to the drill.

手順4

Black and Decker LDX 120C Light Replacement: 手順 4、 1の画像 1

Remove the five screws on the front side of the drill.

手順5

Black and Decker LDX 120C Light Replacement: 手順 5、 1の画像 1

Gently grab both sides of the drill casing, and separate both sides from each other.

手順6

Black and Decker LDX 120C Light Replacement: 手順 6、 1の画像 1

At this point you should be able to separate both as illustrated.

手順7

Black and Decker LDX 120C Light Replacement: 手順 7、 1の画像 1

Now all the components of the drill are visible and can be accessed.

手順8 Light

Black and Decker LDX 120C Light Replacement, Light: 手順 8、 1の画像 1

After following the prerequisite guide the drill is now open and you can see all the components of the drill.

手順9

Black and Decker LDX 120C Light Replacement: 手順 9、 1の画像 1

First separate the top part of the drill, which includes the motor and the chuck, from the rest of the components.
Remove carefully so that wire connection is not damaged throughout this process.

手順10

Black and Decker LDX 120C Light Replacement: 手順 10、 1の画像 1

Then separate the other component which includes the trigger, light, and the connection to the battery.
Do this carefully so that no wire connection or any component gets damaged.

手順11

Black and Decker LDX 120C Light Replacement: 手順 11、 1の画像 1

First check if the connection to the light is not intact.
If the wiring is lose simply reconnect the wire.
Then check if the light bulb is not damaged in any way.
If the light bulb is broken or simply just burnt; simply replace the light bulb.

手順12

Black and Decker LDX 120C Light Replacement: 手順 12、 1の画像 1

Grab the connection of the light bulb.

手順13

Black and Decker LDX 120C Light Replacement: 手順 13、 1の画像 1

Using pliers cut the two connecting wires from the mother chip.
To prevent potential damage to the component, try desoldering the wires. Learn more about soldering here.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

2人の作成者と共同で作成されました。

jeffrey zakka

メンバー登録日: 02/09/16

735 ポイント

6のガイドは作成済み

+11 個以上のバッジ

チーム

USF Tampa, Team 11-5, Cheng Spring 2016 USF Tampa, Team 11-5, Cheng Spring 2016人のメンバー

USFT-CHENG-S16S11G5

5 メンバー

6のガイドは作成済み

0 件のコメント

統計データ:

過去 24時間: 1

過去 7 日: 17

過去 30 日: 61

今までの合計 17,429