メインコンテンツにスキップ

BLU Dash JR D140 Microphone Replacement

必要な工具と部品

  1. BLU Dash JR D140 Microphone Replacement, Battery: 手順 1、 1の画像 1
    • Turn off the phone first. Press the power button continuously for 2-3 seconds to shut down the phone.

    • Using a plastic opening tool, pry open the back cover from the slit on the bottom right corner of the phone.

  2. BLU Dash JR D140 Microphone Replacement: 手順 2、 1の画像 1
    • Using a plastic opening tool or finger, pull out the battery.

  3. BLU Dash JR D140 Microphone Replacement, Microphone: 手順 3、 1の画像 1
    • Remove the four 4.0mm Phillips #1 screws.

  4. BLU Dash JR D140 Microphone Replacement: 手順 4、 2の画像 1 BLU Dash JR D140 Microphone Replacement: 手順 4、 2の画像 2
    • Starting from a corner, separate the panel from the frame using the plastic opening tool.

    • The volume button will pop out.

  5. BLU Dash JR D140 Microphone Replacement: 手順 5、 1の画像 1
    • Unscrew the 3.6mm Phillips #0 screw from the motherboard.

  6. BLU Dash JR D140 Microphone Replacement: 手順 6、 1の画像 1
    • Using a spudger, lift the black ZIF connector at the top left corner of the phone.

  7. BLU Dash JR D140 Microphone Replacement: 手順 7、 1の画像 1
    • Pull the ribbon cable out of the ZIF connector.

  8. BLU Dash JR D140 Microphone Replacement: 手順 8、 1の画像 1
    • When the ribbon cable is removed from the ZIF connector, peel off the power sticky button using a plastic opening tool.

  9. BLU Dash JR D140 Microphone Replacement: 手順 9、 1の画像 1
    • Peel off the volume sticky button.

  10. BLU Dash JR D140 Microphone Replacement: 手順 10、 1の画像 1
    • Separate the screen cover from the motherboard using the plastic opening tool.

    • Make sure that the LCD screen stays attached to the motherboard while doing this.

  11. BLU Dash JR D140 Microphone Replacement: 手順 11、 3の画像 1 BLU Dash JR D140 Microphone Replacement: 手順 11、 3の画像 2 BLU Dash JR D140 Microphone Replacement: 手順 11、 3の画像 3
    • The microphone is at the bottom left corner of the phone.

    • Lift the microphone very carefully. Unsolder the two lower wires (one red wire and one black wire).

    • If you don't feel comfortable with this step I recommend looking at Ifixit's solder guide here.

    • Solder the new microphone in the same spot. The black wire will go in the left spot and the red wire in the right spot.

終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

3人の作成者と共同で作成されました。

Saravpreet singh

メンバー登録日: 07/08/15

179 ポイント

1ガイドが承認済み

チーム

UW Tacoma, Team 1-4, Liner SU 2015 UW Tacoma, Team 1-4, Liner SU 2015人のメンバー

UWT-LINER-SU15S1G4

4 メンバー

2のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 500