修理を始めるには

修理する権利

ストア

Astro A40 TR Internal wiring components Replacement

作成者： Mike (そして 2 人のその他投稿者)
  • コメント: 1
  • お気に入り: 0
  • 完了: 1

難易度

難しい

手順

7

所要時間

15 - 20 分

セクション

2

フラグ

1

Better Introduction

より良い紹介部分

この紹介部分を完成し編集することでこのガイドを改良する

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage. To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    • To access the speakers you need to disassemble the earpiece. First remove the foam ear piece by simply pinching the padding and pulling lightly until the magnets disengage.

    翻訳

  2. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly. Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    • Remove the dust cover located on the speaker. Use the corner of the spudger to peel underneath the cover until you can lift it by hand. The cover is held onto the device with adhesive and should be removed slowly.

    翻訳

  3. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page. Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    • Take off the front cover by removing the four screws located in a square formation on the surface of the device. Use the J00 Philips driver listed in the device page.

    翻訳

  4. The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

    The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

  5. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them. Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    • Locate the three small screws under the speaker. Use the J00 Philips Driver to remove them.

    翻訳

  6. If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • If your issue is asking for the complete replacement of the speaker or the motherboard, un-solder the old components and replace with new speaker by re-soldering.

    • Check out this useful guide on how to solder and desolder connections if soldering is new to you.

    翻訳

  7. Untie the disconnected wiring harness.

    • Untie the disconnected wiring harness.

    翻訳

  8. Pull the black wire out of the hole in the device.

    • Pull the black wire out of the hole in the device.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

2他の投稿者と一緒に

Mike

メンバー登録日: 2016年10月20日

367 ポイント

3のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

UMass Dartmouth, Team 6-5, Martin Fall 2016 UMass Dartmouth, Team 6-5, Martin Fall 2016人のメンバー

UMASSD-MARTIN-F16S6G5

3 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 8

過去 7 日: 42

過去 30 日: 105

今までの合計 4,525