修理を始めるには コミュニティ ストア
リペアコミュニティに参加 - アカウントの作成

Repair guides and support for your Samsung TV.

20回答 すべてを表示 | 6 のパーツ ストア

オプション

Standby light not on

Hi I have a MU6100 so slightly different. My exact model is UA43MU6100S. Issue is standby light is not on. If I unplug the cable between the PSU and mainboard the backlights turn on.There is a test point to measure 8v stby and 13v on this point is always at 13v it will drop to about 8.5 volts for very briefly when connecting back cable to main board when unplugging and measuring voltages pin A/D is 3.2v unplugged and 0.08 connected 0d_US is 3.6 unplugged and 3.3 connectedBLU_PWM is 3.2 unplugged and 0.04 connected power on/off is 4.6 unplugged and 3.3 connected. I have tried disconnecting the 2 LCD flat panel cables to eliminate a panel fault.If I hold the power button on remote a few seconds the standby red lights up for another few seconds then give 1 flash and goes off.

Update (09/02/23)

Block Image
Block Image
Block Image
この質問に回答する 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 1
1件のコメント

[image|3061367][image|3061368]

さんによる

コメントを追加

2件の回答

フィルタ：
参考になった順 新しい順 古い順
最も参考になった回答

オプション

Hi @shaun63172,

Try disconnecting the TV power button board cable from the mainboard and see if the TV turns on using the remote.

This won't work if the IR receiver is on the same board as the power button.

Just wondering if the button is "stuck" in the operated position so the TV doesn't know whether to turn on or off.

If no good, try removing the batteries from the remote and use the TV controls and check

このアンサーは役に立ちましたか？

はい いいえ
スコア 1
コメントを追加

オプション

@shaun63172 we need to see your boards to follow your power measurements. Since your back lights come on it is a pretty good indication that your Power supply is okay. This sounds pretty much like a failed main board.

iFixitでの質問に画像を追加する方法

このアンサーは役に立ちましたか？

はい いいえ
スコア 0

10 件のコメント:

Hi @shaun63172,

Try disconnecting the TV power button board cable from the mainboard and see if the TV turns on using the remote.

This won't work if the IR receiver is on the same board as the power button.

Just wondering if the button is "stuck" in the operated position so the TV doesn't know whether to turn on or off.

If no good, try removing the batteries from the remote and use the TV controls and check

さんによる

Yes have tried disconnecting both boards as well as the WiFi / bluetooth board but still same issue.

さんによる

[image|3061367][image|3061368]

さんによる

@shaun63172 see if you can get some pictured that are zoomed in.It's difficult to enlarge the ones you have attached since they get fuzzy on close up. Typical Samsung. Put more goop on the Mosfets.....what a mess on the board :-)

We need to see the connector CNM803 where the main board connects to.

さんによる

Have added a close up of CNM803

さんによる

5件以上のコメントを表示

コメントを追加

回答を追加する

Shaun さん、ありがとうございました！
統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 7

今までの合計 153