メインコンテンツにスキップ

Repair guides and support for your Philips TV.

243回答 すべてを表示

it started to blink 3 times - Philips TV 42PFL6057

Block Image

Block Image

Block Image

Thanks for all the information.

I have the 42PFL6057H/12

After 10 years, it started to blink 3 times and it does not power on.

What is the diode that I have to replace?

I have many photos.

Thanks in advance,

Francisco

Update (05/04/23)

Thanks a lot.

After checking all the diodes, apparently the is failure is in the ZD904 and in the ZD717

Does anyone know what sort of diodes are they?

I send you an attached photo.

Block Image

この質問に回答する 同じ問題があります

この質問は役に立ちましたか?

スコア 1

1件のコメント:

Thanks a lot for your answers.

I am going to check the diodes tonight.

Can you recommend me any online electronics shop to order the material from Spain/Europe?

さんによる

コメントを追加

3件の回答

@franciscorm it may not be a diode but it may be the power board. The 3 blink code is a non-specific code. All it means is that your TV went into Protection mode. Check D603 as the primary suspect. If it checks out okay, you will need to check the other diodes as well.

このアンサーは役に立ちましたか?

スコア 0

6 件のコメント:

Thanks.

Checking with or without AC current?

さんによる

@franciscorm you can just check for function without powering up the TV.

さんによる

Thanks a lot for your answers.

I am going to check the diodes tonight.

Can you recommend me any online electronics shop to order the material from Spain/Europe?

さんによる

@franciscorm Mouser.com has a European site. They are costly when it comes to shipping, but their components are good quality.

さんによる

Thanks a lot.

After checking all the diodes, apparently the is failure is in the ZD904 and in the ZD717

Does anyone know what sort of diodes are they?

I send you an attached photo.

さんによる

1以上のコメントを表示

コメントを追加

Thanks a lot.

After checking all the diodes, apparently the is failure is in the ZD904 and in the ZD717

Does anyone know what sort of diodes are they?

I send you an attached photo.

Block Image

このアンサーは役に立ちましたか?

スコア 0
コメントを追加

Hi!

All the measures are made with the "diode" mode of the multimeter.

*ZD904: The measure is low in comparison with the other zeners. In addition to this, the multimeter "beeps" like checking a fuse.

*ZD717: The measure is low in comparison with the other zeners.

I attach two photos

Block Image

Block Image

このアンサーは役に立ちましたか?

スコア 0

11 件のコメント:

@franciscorm sounds reasonable. Time to replace those diodes.

さんによる

Thanks, but, how do you know what sort of model are they in order to buy it?

さんによる

@franciscorm that is a tough one without having the schematic which identifies the components. Yours appear to have a glass body. We know that lower wattage zeners usually have glass bodies, higher wattage ones have the common black body. See if you can take a voltage measurement on the Zener diode adjacent to the one you need to replace.

さんによる

Diode mode in the multimeter:

ZD905➡️699

ZD902➡️669

ZD601➡️682

ZD717➡️110

ZD903➡️526

ZD904➡️0

D801➡️469

ZD602➡️538

D603➡️538

D950➡️180

D951➡️180

D901➡️527

D906➡️529

さんによる

@oldturkey03 If ZD717 and ZD904 are the ones who fail, ¿which are the similar ones in order to know what to buy?

Maybe the "couple" of the ZD904 is the ZD 903, but for the ZD 717...

Thanks in advance 😀

さんによる

6件以上のコメントを表示

コメントを追加

回答を追加する

Francisco RM さん、ありがとうございました!
統計データ:

過去 24時間: 1

過去 7 日: 6

過去 30 日: 28

今までの合計 279