Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

Question

Whirlpool Dishwasher

Repair information for Whirlpool dishwashers.

156回答すべてを表示

Maroš Ondruš @marosondrus

評価: 11

1

投稿日: 2023年4月17日

オプション

Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

Good day, I would like some advice regarding the dishwasher (brand above). The dishwasher stopped draining water, if I remove the water manually, the dishwasher starts the program and after a few minutes the cycle stops. If I turn on the dishwasher even with water inside, it just beeps and the start light flashes quickly and the display shows the number 3, if I put the dishwasher in diagnostic mode, the start light flashes 10 times and the display shows the number 2. Can anyone help me, what could this be? ? I cleaned the drain and the filters. I am concerned that it will be the pump or something related to it (stuck, stopped working). I will be grateful for any advice. Thnx

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 0

コメントを追加

1 件の回答

ベストアンサー

jayeff @jayeff

評価: 450.2千

11

367

1.4千

投稿日: 2023年4月17日

オプション

Hi @marosondrus ,

Here's some info that may help or maybe not.

Here's a link that shows that the error (#3) may be a problem with the heater or heater circuit or perhaps the temperature sensor (examples only to show what they look like and how much they may cost).

Fault diagnostic code of 10 flashes also indicates a sensor problem.

Hopefully this is of some help.

Unfortunately I can't find a service manual or a wiring schematic which would make it easier to test them using a meter.

このアンサーは役に立ちましたか？

はいいいえ

スコア 2

6 件のコメント:

I'm at work at the moment, but when I get home, I can easily take pictures and add them here, because I seriously don't know what it means anymore, I don't understand why the water doesn't drain, or if the sensor has any effect on the fact that the water remains in the dishwasher. I looked at the site, but most of the errors are described in F(X) codes.

Maroš Ondruš さんによる2023年4月18日

https://beko.elektrahk.cz/482000032666-c...

Maroš Ondruš さんによる2023年4月18日

@marosondrus

It might be that it isn't even starting because the water is not hot enough, therefore it won't drain after filling etc

Here's how to easily add images to your question on ifixit iFixitでの質問に画像を追加する方法

With the power disconnected from the dishwasher you should be able to use an Ohmmeter and check both the sensor and the heater for continuity. They should not test open circuit.

Unplug them and test directly across their connection terminals.

jayeff さんによる2023年4月18日

As I wrote above, if I manually remove the water from the dishwasher, the cycle and the program start to work, then it works for about 20 minutes, the water is heated, but then it stops and stops working and the water is not pumped out. I think the heating is fine, but probably the sensor is not... But that's just my theory, it doesn't matter at all in these machines. And thanks, I'll try to take pictures of the problems after lunch.

Maroš Ondruš さんによる2023年4月18日

I have no idea what's happened, but I tryed again same Diagnostic Code (Start, 2x Program Button, Start, 2x Program Button, Start), now and water was suddenly drain out. Also I tryed rinse Program and everything went fine. Can someone explain me what's happened, because actually I really don't understand, I tryed IT Yesterday few times and nothing happen.... But anyways Thanks You man for your time.

Maroš Ondruš さんによる2023年4月18日

1以上のコメントを表示

コメントを追加

I'm at work at the moment, but when I get home, I can easily take pictures and add them here, because I seriously don't know what it means anymore, I don't understand why the water doesn't drain, or if the sensor has any effect on the fact that the water remains in the dishwasher. I looked at the site, but most of the errors are described in F(X) codes. — Maroš Ondruš
@marosondrus

It might be that it isn't even starting because the water is not hot enough, therefore it won't drain after filling etc

Here's how to easily add images to your question on ifixit iFixitでの質問に画像を追加する方法

With the power disconnected from the dishwasher you should be able to use an Ohmmeter and check both the sensor and the heater for continuity. They should not test open circuit.

Unplug them and test directly across their connection terminals. — jayeff
As I wrote above, if I manually remove the water from the dishwasher, the cycle and the program start to work, then it works for about 20 minutes, the water is heated, but then it stops and stops working and the water is not pumped out. I think the heating is fine, but probably the sensor is not... But that's just my theory, it doesn't matter at all in these machines. And thanks, I'll try to take pictures of the problems after lunch. — Maroš Ondruš
I have no idea what's happened, but I tryed again same Diagnostic Code (Start, 2x Program Button, Start, 2x Program Button, Start), now and water was suddenly drain out. Also I tryed rinse Program and everything went fine. Can someone explain me what's happened, because actually I really don't understand, I tryed IT Yesterday few times and nothing happen.... But anyways Thanks You man for your time. — Maroš Ondruš

Whirlpool Dishwasher

Whirlpool Wric 3c26 Error Code 10 - 2 / flashing light + number 3

1 件の回答

回答を追加する