修理を始めるには コミュニティ ストア

2016年9月16日に発売。モデル番号は1778,1784。 GSM かCDMAの32、128、256GBがあり、色はローズゴールド、ゴールド、シルバー、ブラック、ジェットブラックがあり。

1364回答 すべてを表示

オプション

*help* problems after repair

So, I was restoring an iPhone 7 Plus. I replaced the Chassis, LCD and Battery.

I transferred literally everything over from the old chassis to the new one, same with the LCD. I come to power on the device and I’m hit with a bootloop. After about 5 minutes of boot looping, it turns on BUT it says Searching at the top and my battery is showing 1% (on the new and old battery, I’ve tested both). It is not charging at all and whenever I turn it off, it goes back to boot looping.

I’ve tried the old lcd and battery but no luck there. The front camera flex is fully connected, I even tried when it was disconnected! What is happening?!

Bearing in mind, the phone was fully functional before I started this repair.

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

3件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

Hi,

Are you using the original charging port?

A lot of times the replacement chassis come with charging port connection issues, this will cause no service issues and also cause the boot loop your describing.

If you transferred over the old port you need to go back and check it for any tears.

このアンサーは役に立ちましたか？

はい いいえ
スコア 1

5 件のコメント:

Hi,

I transferred everything, including the original charging port. Is it most probably the charging port though? If so, I shall order a replacement one.

さんによる

Hi,

I would order a new charger port flex. I think that would fix all the issues your experiencing.

さんによる

Okay, I will update you when I’ve replaced it. Cheers!

さんによる

This worked a treat! Thank you very much.

さんによる

Hi, happy I could help, it’s always worth trying the basics before we go down the micro soldering route. That’s the way I work in my workshop anyway.

さんによる

コメントを追加

オプション

sounds to me like the baseband cpu is shorted. if thats the case theres no way to fix it.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0

1件のコメント:

Would it be worth trying a new sub pba though?

さんによる

コメントを追加

オプション

Hi Liam,

as we all (microsoldering cominity) know that

iphone 7/7 plus board have diseases same as we faced back in IPhone 6/6 plus touch deseas and baseband deseas.

and this happenes because of stretch/shock or any kind of compact.

and if you search iPhone 7 rear down on Ifixit.

you ll find out the baseband and audio ic on iPhone 7/7 on opponent side of the board but at the same place.

now boot loop on iPhone 7/7plus is either home button or audio ic. If your home button is ok than it’s look like audio ic and baseband which make more sense as they are at the same spot of the board. To check go to dialling pad and press *#06# if you dobf get imei the basebNd needs rebelling and it’s repairable. To find out audio ic go to recording and try to record something if it says faild or no audio found error it means audio ic needs jumpers with audio replacement this is repairable too.

Not easy but possible.

i am saying this because that’s what I do everyday.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0

2 件のコメント:

I’ve just tried *#06* and nothing happens. Definitely the baseband IC then? Also the is no audio coming from videos.

さんによる

So as I have explained in my comment. Baseband amd audio both needs sorting in you iPhone. bootloop is caused by audio ic and no service is caused by baseband. Before asking for repair you need to check whether it’s Qualcomm board or intel board?

And it’s happened because of may be the old housing was stretch/bent or you might have bent the board while replaceing the housing.

さんによる

コメントを追加

回答を追加する

liam.jk1 さん、ありがとうございました！
統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 185