u4020 critical to boot?

Question

iPhone SE

2016年3月に発売された4インチのiPhone。ハードウェア仕様は6sに類似しています。シルバー、スペースグレイ、ゴールド、ローズゴールドのカラーが揃っています。16/64 GB容量、Model A1662とA1723

1050回答すべてを表示

Elliot @elliot1

評価: 127

5

投稿日: 2018年12月18日

オプション

u4020 critical to boot?

Good afternoon,

I'm just researching a water damaged iPhone SE that initially had a VCC_Main shorted that was alleviated by removing one cap.

When connecting to power now, it draws 0.43mA / 0.44mA and U4020 LED Driver gets really hot (freeze spray used to detect).

It controls the "LED Driver" and schematics says it is critical. Is it critical for boot? or if we remove this should we be able to artificially use a light and go into the screen layers?

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 0

コメントを追加

1 件の回答

ベストアンサー

Minho @refectio

評価: 221.5千

15

290

807

投稿日: 2018年12月18日

オプション

Just to confirm, U4020 is not Stockholm but the Backlight Driver IC. A damaged or defective backlight driver doesn’t stop the phone from booting, unless it is pulling down PP_VCC_MAIN. So check VCC_MAIN to see if it is short or or not giving the proper voltage.

Obviously, a missing backlight driver doesn’t affect the boot either.

You should also probe the backlight circuit as if U4020 is hot, then one of the caps may be shorted on the output side.

このアンサーは役に立ちましたか？

はいいいえ

スコア 3

6 件のコメント:

Thank you Minho, Not sure how I got this confused thinking it is Stockholm, must have had different schematics up or something. Will check the VCC_Main voltage and see

Elliot さんによる2018年12月19日

VCC_Main is low! 2.9V, I will remove this and see if it helps things.

Elliot さんによる2018年12月19日

VCC_Main short up to 3.6V now but still power being drawn is 0.45mA, no obvious signs of heat but removing this chip helped because there was a lot of corrosion, even under it!

Any ideas of probing further with this at all? I really appreciate your help!

Elliot さんによる2018年12月19日

What do you mean by "VCC_Main short up to 3.6V " ?

Minho さんによる2018年12月19日

Using a multimeter in DC voltage mode VCC_Main is reading at 3.68V, before removing the LED Driver this was a lot lower

Elliot さんによる2018年12月19日

1以上のコメントを表示

コメントを追加

Thank you Minho, Not sure how I got this confused thinking it is Stockholm, must have had different schematics up or something. Will check the VCC_Main voltage and see — Elliot
VCC_Main is low! 2.9V, I will remove this and see if it helps things. — Elliot
VCC_Main short up to 3.6V now but still power being drawn is 0.45mA, no obvious signs of heat but removing this chip helped because there was a lot of corrosion, even under it!

Any ideas of probing further with this at all? I really appreciate your help! — Elliot
Using a multimeter in DC voltage mode VCC_Main is reading at 3.68V, before removing the LED Driver this was a lot lower — Elliot

iPhone SE

u4020 critical to boot?

1 件の回答

回答を追加する