3DS XL turns off when pressed in a certain place or knocked/nudged?

Question

ニンテンドー 3DS LL

ニンテンドー3DSは任天堂の最新モデルです。より大きいスクリーンに、より長くなったバッテリー寿命と改良されたデザインが特長です。

413回答すべてを表示

締切られた回答

MelissaMkay @melissamkay

評価: 23

1

投稿日: 2016年5月2日

オプション

3DS XL turns off when pressed in a certain place or knocked/nudged?

Hello!

I've been having this problem for a while now, but only just thought to ask a question about it.

So I have a 3DS XL which was bought for me on Christmas day, 2013.

I was forever dropping it (Bare in mind that I was 8 or 9 at the time) but I never thought anything would happen.

Now here's the problem, sometimes when I accidentally knock the screen or the whole system, it turns off - but there's also another thing. If I press (Gently or hard it doesn't matter) the WHOLE system just turns off too. It bothers me as it resets the date and time at the same time.

Now I can avoid the problem by not knocking it or touching the area, I would just like an explanation of why that's happening.

Thank you for reading.

P.S: I know it probably doesn't matter but one screen is darker than the other.

Picture(s) of the area I can't touch or it'll turn off:

*Click Here*

回答がありました！ 回答を表示同じ問題があります

この質問は役に立ちましたか？

はいいいえ

スコア 0

コメントを追加

2件の回答

ベストアンサー

Andrew Fillhart @zerrian

評価: 1.2千

7

5

1

投稿日: 2016年5月5日

オプション

Okay, from the sounds of it, you've either got a faulty ribbon on your lower LCD or you've got some bad solder points in that area. My guess is the 1st one.

You can trouble shoot this by disassembling your bottom section to the point where the LCD is sitting free. You'll need to have the battery in place too so seating the board back into that ½ of the housing could help. Once you can power it on with the LCD free, try titling it's position a bit and touching that same area. Also moving the LCD from an altered position to it's "sitting" position may provide similar results of it shutting down. If this is the case, you'll need a new LCD.

If the LCD is free and you're not getting those results, check the PCB (printed circuit board) in that area for bad solder points or traces. From there, you may need to resolder something or bridge a burnt out trace.

Hope these suggestions help get your machine up and running again.

このアンサーは役に立ちましたか？

はいいいえ

スコア 1

コメントを追加

Andrew Fillhart @zerrian 評価: 1.2千 7 5 1 · Answer 1 · 2016-05-05T09:17:27-07:00

I had a similar problem with a NDS Lite that I started repairing (it was the first one I started on so errors were made) and when I touched in about the same area, the entire system would short out and shut down. So from what I've learned via trial and error and watching videos from RetroGameTech is that either:

Your lower LCD has a short in the ribbon somewhere
The PCB possibly has a damaged trace in that area. You'll want to inspect that to see if there are any burnt or odd markings in there.

I have a feeling it's probably a faulty lower LCD though. How you can test it is by dismantling the lower section and put it all back together without the middle housing. Put the back on and pop the battery in and then turn it on, shift the LCD just a bit and see if moving it around shuts it down as well or touching it in that area.

If it turns out the PCB has broken traces and such, you'll either need to bridge those areas with solder or possibly run some wiring to both ends.

I hope these help you out.