修理を始めるには コミュニティ ストア

iPhoneの第２世代モデル。モデル番号はA1241 / 8 もしくは16 GBの容量/ ブラックもしくはホワイトのプラスチック製背面ケース。修理はオリジナルiPhoneに比べて直接パーツに作業ができます。ドライバー、こじ開けるためのツールと吸盤カップが必要です。

1169回答 すべてを表示

オプション

What do the numbered ribbon cables do specifically?

I recently replaced a cracked display, and also a battery in my iPhone 3G. Worked great for a few weeks until the white screen of death started to appear when I press the menu button or the power button. Lately it is getting worse. I can get the display to work with persistance, but it's a pain.

I am wondering if maybe one of the cables is loose or something. I have taken it a part a few more times and disconnected and reconnected a few of the ribbon cables, (helps a little bit- but the white screen eventually returns) but I would like to know what ribbon cable corresponds to the display, or what part I can look at to see if maybe I reconnected it poorly.

anyone?

回答がありました！ 回答を表示 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 3
2 件のコメント

Is this the part you're talking about? iPhone 3G/3GS Headphone Jack Assembly

さんによる

no, I mean the ribbon cables that are labeled 1, 2, 3, 4, 5 and 6. like this one, for example:

http://s1.guide-images.ifixit.com/igi/pw...

さんによる

コメントを追加

4件の回答

フィルタ：
参考になった順 新しい順 古い順
ベストアンサー

オプション

Cable 1 LCD display

Cable 2 Touchscreen sensor and home button

Cable 3 earpice speaker and proximity sensor

4,5,6 are I believe GPS, antenna and camera cables.

That is what I can tell by opening it up.

このアンサーは役に立ちましたか？

はい いいえ
スコア 6

6 件のコメント:

You are correct about most of them- However, 4,5 & 6 are actually dock connector, headphone/volume/power/vibration, and antennas, respectively. :)

さんによる

thanks

さんによる

Good to know Josh.

さんによる

Very strange, I snapped part of the volume rocker cable (as we know connected to the earphone jack and power) now my home button isnt working, what do you think is up with that!? any help? thanks :)

さんによる

This was very helpful. I am the kind of person who likes to check things before finishing up. I had the screen lose before tightening the last two screws and tried testing it but the home button was not working.

The reason the home button was not working was because it is connected once you push the screen in closed.

Once again, very helpful and good information. Thanks!

さんによる

1以上のコメントを表示

コメントを追加

オプション

the home button has it's own contacts that connect when the device is closed, it isn't fed through ribbon cable 2

このアンサーは役に立ちましたか？

はい いいえ
スコア 4

2 件のコメント:

quite right, well spotted! +

さんによる

I would advise people to be careful when opening and closing their iphone's, as i managed to break the little contacts off (both of them) and had to solder two small wires bent in a "U" shape, to replace the functionality of the previous contacts.

さんによる

コメントを追加

オプション

Although the home button is a separate entity and connects upon closing, if cable four is disconnected the it will not work.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

オプション

sometimes the ribbon on the display lcd goes bad and you will get a white screan. replace full assemble should work . i had the same problem replaced the full lcd srean and it works great. good luck.

このアンサーは役に立ちましたか？

はい いいえ
スコア 0
コメントを追加

回答を追加する

James Elston さん、ありがとうございました！
統計データ:

過去 24時間: 0

過去 7 日: 5

過去 30 日: 31

今までの合計 72,484