修理を始めるには コミュニティ ストア

iPhoneの第4代目で、修理はそのままパーツを直接交換するだけです。しかし、正面ガラスとLCDはセットで交換する必要があります。容量はGSM / 8,、16m32 GB / モデル番号 A1332 /本体カラーは黒と白色

2375回答 すべてを表示

オプション

iPhone 4 GSM Water Damaged, turns on when connected and Reboots

Hello everyone,

I have an iPhone 4 32 gb At&t.

I saw some corrosion around the logic board components, so I put it in Alcohol for 2 days and brushed it well.

I also put a new battery and Dock connector since the water sensor on it was red.

The phone itself does not power on by pressing power button, however, it turns on when connected to power outlet or pc and reboots consequently.

iTunes does not recognize it as well as Redsn0w.

Please help me to figure out this problem.

Update

Hello again,

Does anyone have any idea what should I do at this point.

I have replaced the broken coil and washed it with alcohol one more time and it still reboots and does not power on with Battery.

Your thoughts are appreciated.

この質問に回答する 同じ問題があります

この質問は役に立ちましたか？

はい いいえ
スコア 1
コメントを追加

3件の回答

フィルタ：
参考になった順 新しい順 古い順
最も参考になった回答

オプション

I have been able to repair some iPhones by scrubbing with alcohol, but I have never used a soaking method. Usually a 99.9% pure alcohol and a few minutes with a sturdy toothbrush will do the trick.

I would try once more to simply scrub the board and see if it will stay on with being pluged into power directly (not to PC). If not then there may be little hope

このアンサーは役に立ちましたか？

はい いいえ
スコア 2

1件のコメント:

Thanks for your respond,

I did try to just brushing it with alcohol, and I noticed that there is a component there by the Power Management IC which it looks like cracked.
Here is couple of pictures that specifies the IC:
http://www.ifixip.com/upload_Pictures/Sc...
http://www.ifixip.com/upload_Pictures/IM...
what should I do at this point? Can I find this IC? if so what does it called?

さんによる

コメントを追加

オプション

Kia, yes it looks like that part is broken. It is one of the power inductors and could be the cause for your problems. Of course you do want to make sure that all corrosion is removed and that you phone is clean. The part that is broken is a coil, with an Apple designation of L17_PMU, and the values are 2.2UH-1.5A-98MOHM. Now, you can most certainly try and obtain one from places like Mouser.com or digikey.com. Here is a pretty close match and should work for you. Hope this helps, good luck.

このアンサーは役に立ちましたか？

はい いいえ
スコア 2

6 件のコメント:

Thanks for your detailed information. I did order that coil from the link you provided me.

Since you're the expert, can you tell me how to take it off of the logic board, and how to put the new one back in? What equipments do I need for this job?

Best,

さんによる

Kia, I most certainly am not the expert :-) The coil is an SMD device and best way to solder it on is via a hot air rework station. but you also use a very fine soldering iron. You have experience with that?

さんによる

Well, I don't want to ruin the logic board. that's why I asked about the equipments. Do you think http://www.digikey.com/product-detail/en... or somthing close to this would do the job for me?

さんによる

lools like a little on the hot side with the 100W but it could work. Since it seems like you are new to this, check out this video and download my favorite guide from here.

さんによる

It looks like that I have everything that I need for it. I have to wait for the coil. I will update when I get into it. Thanks everyone for your advices.

さんによる

1以上のコメントを表示

コメントを追加

オプション

but you also use a very fine soldering iron. You have experience with that?

how i can i can ??

このアンサーは役に立ちましたか？

はい いいえ
スコア 0

1件のコメント:

Yes, Mr. Morteza. I have experience of soldering connectors on 3g series.

it's always good to see a country-mate.

Thanks for asking though

さんによる

コメントを追加

回答を追加する

Kia さん、ありがとうございました！
統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 924