LCDスクリーンのバックライト
LCDを搭載したすべてのiPhoneのバックライト回路は、共通のアーキテクチャを採用しています:
- パワーチップがバックライト信号を生成。
- 一般に「バックライトコイル」と呼ばれるインダクタが信号を増幅します。
- ダイオードが逆電圧を防ぎます。
- フェライトビーズが信号をフィルターします。
- リボンケーブルが信号をバックライトLEDストリップに運びます。
- デバイスによっては、バックライトドライバー チップが追加されています。
バックライト故障の原因のトラブルシューティング
ほとんどのiPad/iPhoneハードウェアは1.8V~5.2Vの電圧で動作しますが、バックライト回路は約15~20Vで動作します。また、高電圧のバックライト回路は、水濡れによる腐食も起こしやすい傾向があります。
ディスプレイ故障の最も一般的な原因
- LCDスクリーン - LCDの故障は、落下による損傷、水による損傷、または単に部品の欠陥の結果として発生する可能性があります。
- バックライトフィルター - バックライト回路がショートすると、フィルター内部の細いワイヤーが断線し、バックライトLEDからの電力が遮断されます。
- バックライトダイオード-バックライトフィルターと同様、バックライトダイオードも壊れやすい部品です。バックライトフィルターが特に焼けている場合、ダイオードも故障していることがよくあります。フィルターに損傷がないのにダイオードが故障することはまれですが、起こり得ます。
最近のiPhoneでは、インダクタコイルが故障の原因になることはほとんどありません。
バックライトショートサーキット
最も一般的なショートの原因は、バッテリーを接続したままデバイスを操作することで発生します。 画面が暗くなっても、バックライト回路には電圧があります。ピンセットがずれたり、LCDコネクタの位置がずれたりすると、バックライト回路がアースにショートする可能性があります。(iPadミニは特にこの故障が起こりやすく、フレックスケーブルをコネクタに抜き差しする際、少し角度をつけるだけでバックライトの高電圧ピンと隣接するグランドピンがブリッジしてしまうためです)。デバイスの作業前に必ずバッテリーを外せば、自己誘発的なショートを避けることができます。
バックライトショートのもう一つの原因は、組み立て手順の誤りです。iPhoneの画面には、LCDフレックスケーブルに、LEDライトストリップに電力を供給する、より細いバックライトフレックスケーブルを接続するはんだ接合部があります。デバイスを製造する際、このはんだ接合部は黒いテープで保護されていますが、スクリーンを再生する工程でテープを交換しなかったり、ずれた位置に貼ったり、しっかりと貼っていないメーカーがあります。その結果、テスト時には正常に動作するものの、金属製のLCDシールドを取り付けると、露出したはんだ接合部がアースされたフレームに接触し、バックライト回路がショートしてしまいます。
バックライトのショートは、LCDフレックスを固定するZIFコネクタのラッチが欠けている場合に発生する可能性があります。 LCDフレックスが斜めにスライドし、高電圧バックライトピンが接地ピンに接触してショートします。
その他の一般的なバックライト故障の原因
バックライトの故障の原因としては、水濡れがよく挙げられます。
液体侵入によってLCDコネクタのピンとパッドの接合部が腐食し、コネクタへの電気経路が断たれ、フィルタが損傷する可能性があります。
バックライト回路の故障は、回路基板上の電気トレースの損傷によっても発生する可能性があります。例えば、基板を大きすぎるネジで固定しようとして、基板に埋まっている電気配線が不注意で切断された場合、バックライト回路はバックライトLEDに電力を供給できなくなります。
バックライトの故障を診断する
お使いのデバイスが「死んでいる」のか、単にスクリーンが故障しているだけなのか診断するには、コンピュータに接続してみてください。コンピュータがデバイスを認識する場合、問題はおそらくLCDスクリーンまたはバックライト回路にあります。また、iPhoneはバックライトの問題をチャイム音と振動で繰り返し知らせます。
朗報は、ほぼすべてのバックライト故障が修理可能だということです。 損傷した部品を特定したら、交換するだけです。自分で修理できない場合は、知識のあるマイクロソルダー専門店に連絡し、迅速に修理を行いましょう。
以下の翻訳者の皆さんにお礼を申し上げます:
100%
Midori Doiさんは世界中で修理する私たちを助けてくれています! あなたも貢献してみませんか?
翻訳を始める ›
25 件のコメント
Very good information to know thanks
Oumar Mansare - 返信
Very good information, but what you are referring to as a "filter" is in fact a fusible link, on a circuit you will find it abbreviated FL, it is in fact a fuse and not a filter.
funkyman - 返信
FL means fusible link. You are correct.
Kevin Hamby -
No I don't think so
diane parrino - 返信
thanks very good
Mehmet Yelden - 返信
That's good advice
Andre Petetan -
Thanks for the advice
Andre Petetan -
Do you know anyone who might fix my inoperable ipod touch 4th generation? Model A1367, C3VJT1S WF96T. I have used it for 5 years, never dropped or damaged it. But it parted front from back and is inoperable. Bought new and still looks like new. Mostly used for music. Thanks in advance.
patricia dotson - 返信
Hello, i try to repair my ipad air 2. I pull Down the old Digitizer and Touchscreen and try the new Digitizer. It works fine but after then i forget to turn down the ipad, i just pull down the cables from Mainboard. Now if i connect new or old Digitizer i cant see anything, Power Button is also without funktionalit. I hear sound if i connect ipad to pc. What can i do now, is my mainboard dead?
Vi T - 返信
Just try removing the battery again and reconnecting it. It should boot back up with image.
jcaldwell89 -
very good information keep it up
Sharath kumar - 返信
is there some site where i can find out what voltage the back light strip needs to run?
Josh McLaughlin - 返信
How to remove a virus
danieljohnson66 - 返信
How to remove a virus on my ipad air
danieljohnson66 - 返信
Pengisi daya tidak masukhanya logo apel yang munculkelapklip apamasalah
Hendra Fang - 返信
Is this applicable for lcd of semi autohemistry analyzer?
francism.bacay - 返信
if it is 15-20v then will it operate at all if i send 12v?
what about 5v?
i am making sculptures from backlights - just ordered some.
ari - 返信
Good day
Pls assist me, my sunsui TV 50 inch backlights are always burned down what is the causes
Tuwani Mudau - 返信
how much voltage output
umer - 返信
What is most likely causing the VIZIO backlight malfunction when the backlight does finally come on after multiple attempts. Once on, it stays steady and bright until turned off. It might normally come back on the next time it is powered up.
JR Tan - 返信
I have a battery powered backlit LCD clock that I bought at a thrift store and when I inserted batteries, I found the LCD backlight remains on as well as all the digits and indicators "light" up until I take them out. Any idea what could be causing this and if its repairable? Thanks in advance.
Ruben Martinez - 返信
This backlight circuit has to side a left and a right one side have a continuous voltage and the next side have a one time plus. What could cause this problem?
akeem lavia - 返信
I am trying to find instructions for my LCD Color digital backlight
I put in batteries, Programed it and it shut off. Not a ckue
Jacki Smith - 返信
Sony tv bravia 40” switch off and switches on in about 30 seconds
Is it due to backlight problem ?
ashok kalburgi - 返信
One question
Is it possible that the LED of TV fail by the short circuit?
And if yes, whether its symptom could be such as a hit on screen?
Asemaneh Allame - 返信