Erik Eriksson

Hello! :D Background / Information: My laptop sometimes gets really hot, the CPU goes up to over 90 degrees Celsius (not...

Cause of the problem: My guess would be that a lot of dust and other debris has gotten stuck around something, which stops the part from spinning smoothly. It may also be that the debris has forced a part away from where it’s supposed to be. I have another brand of a robot vacuum that I'm taking apart and cleaning now and it really needed cleaning, it didn’t have the same problem as yours but I found a few places where it looked like it would cause a similar problem anytime. How to turn it upside down and it still runs: From my understanding, you should be able to turn it upside down by holding the wheels down, I think that’s the mechanism detecting if it’s on the floor or not. How to solve it: If you feel comfortable with taking it apart and clean it from dust etc., that’s what I would begin with. If you find what part it is that sounds bad and don’t want to clean the other moving parts when you're on it, you can go for just that one. I found two guides on how to get to the Cleaning Head and Side Wheels,...

Since you have a new cable, the cable shouldn’t be the problem. Start with disconnecting the ribbon and look if a part of the old ribbon may have got stuck in the connector. Then connect the ribbon again by inserting it again and make sure it is all the way in without using that much force, then close the latch to lock the ribbon in place. If this doesn’t help, a local repair professional should be able to replace the connector for you without it being extremely expensive, make sure to ask for how much they think it will cost before. (I'm not 100% how the connector looks, but it should be possible) Hope this helped you and good luck! :D

Replacement Part: I found that they are selling new ones on their own website, if you have the headphones that you choose as the device you can find the replacement here. If you are in another country than the selected one, you can change it by clicking the flag in the top right corner. Removing the ear cushions: It seems like you should be able to gently pry them of using your hands, here is a video I found on someone doing it. Jabra Move earpad replacement

It’s hard to know exactly how long the screws are without anything to measure them with. What I would do is to take the stripped screw and compare it to the other screws, start by removing the ones that are obvious, then removing by length etc. and then you should end up with a screw of the right size. Hope this helped and good luck! :D

Before trying anything else, plug in another electrical device into the wall socket you are using for the computer, just to make sure it’s not a problem with the wall outlet/fuse. If the other device works using the same outlet, it sounds to me like a power supply problem. (I’m pretty new to repairs, so don’t take my words for 100%) iMac Intel 27" Retina 5K Display Power Supply Replacement

I don’t know exactly how the sensors that are detecting if the basket is full or not, but here is what I would start with. The first thing I would do is to try and clean both the basket and the area where you put the basket in the vacuum using a damp (not so there is dripping water, squeeze out almost all of the water) piece of paper or cloth. The problem may be that the sensor detecting if the basket is full or not have been covered by dust or something else that makes it to think it’s full all the time.

After searching for it a little bit I couldn’t find any spare wheels for your model. If I understand you correctly, you are planning to replace all four wheels, so it would work if you get any wheels that have the same mountings and are about the same size as the old ones (just measure so they are big enough so the body isn’t laying on the ground and small enough to fit). If you add pictures and measurements for the mounts and the size of the wheels, then someone may be able to found some that fit. iFixitでの質問に画像を追加する方法

In theory, it should still be “water resistant “ after you replace the battery (this if you also replace the original adhesive). But in reality, it probably isn’t going to be 100% “water resistant“, it’s extremely hard to get a perfect seal that stops all moisture. I wouldn’t even trust that it really is that when it comes from the factory. Depending on how you manage to place the new adhesive, it should work to stop most moisture to come into the device. But I would recommend using a waterproof case if you are planning on taking a swim whit the device on you or something like that when you have the device underwater for a longer period of time (this even without opening the device up). Hope this answered your question. :D

Step 1:: To begin with, you can follow this guide for the TI-84 PLUS Silver Edition of how to get the backplate off, ignore step 1 and 2 in the guide (don’t know if you can do it on your device and it’s not necessary from what I can see). TI-84 Plus Silver Edition Motherboard and Screen Replacement Step 2 - Choose alternative A or B:: A: When you have got the backplate off and it’s looking to be the same as in the guide, then you should be able to follow the guide. Keep a bit extra attention for every step so it’s looking the same as yours, the guide isn’t for the exact same model as the one you have. B: If it doesn’t look the same, then add a picture of how it looks in your question if you don’t find how to do it yourself. iFixitでの質問に画像を追加する方法

It’s a bit hard to say without trying things myself, but I can give a few tips on what you can try. 1: Find something to use as a prying tool. If you have an iFixit Kit I would recommend metal prying tool and the prying pics. Otherwise, a thin food knife will work fine and for the prying pics, you can cut out small pieces from a hard plastic package that you don’t use. 2: Carefully try prying at different places in the gap between the bottom piece and the top. Try inserting the metal prying tool/knife in the gap between the top and bottom pieces, carefully pry and just try to feel if it feels to be stuck at the edge or in the middle of the toy. A: If you ut seems like it is stuck at the edges, it’s probably clips holding down the part. B: If it seems to be stuck in the middle, there may be a hidden screw from the top stoping the pice from getting lose. 3: Depending on if it was A or B in the second step, choose the responding one below. A: Carefully insert the metal prying tool/knife (not that far, just a...

It was a while ago you wrote this, but I will reply in case you still have the problem or anyone else is reading this in the future.

This is not the correct place to contact iFixit for this kind of thing, you should contact the customer support instead.

iFixit Customer Support