メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

This break down will enable you to dismantle your ipod nano 1st generation without breaking it.

この分解は修理ガイドでは ありません。 お持ちのiPod Nano 1st Generationを修理する際は、iFixitの修理ガイドをご利用ください。

  1. 1.    Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool into the connection point. This should pop the case off. Note that force will need to be used. 1.    Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool into the connection point. This should pop the case off. Note that force will need to be used.
    • 1. Using an ipod unclipping tool (which could be a knife or similar to it), unclip the outer casing by putting the tool into the connection point. This should pop the case off. Note that force will need to be used.

    Holy cow! That battery is bulged!

    Lucas Hoekstra (Lucas9810) - 返信

  2. 2.    Remove the circuit board by unscrewing the 3 screws that hold it down. Note that specialised screwdrivers may need to be used.
    • 2. Remove the circuit board by unscrewing the 3 screws that hold it down. Note that specialised screwdrivers may need to be used.

  3. 今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

    今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る
  4. 3.    Remove battery by carefully detaching the connect wire that’s connected to the circuit board. Note that tweezers may need to be used to help pull the tab out. 3.    Remove battery by carefully detaching the connect wire that’s connected to the circuit board. Note that tweezers may need to be used to help pull the tab out.
    • 3. Remove battery by carefully detaching the connect wire that’s connected to the circuit board. Note that tweezers may need to be used to help pull the tab out.

    Is it just me or does it look like that battery is about to burst?

    TuxRug - 返信

    Wow, yeah that thing is toast.

    Andrew Bookholt -

  5. 4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover. 4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover. 4.    The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover.
    • 4. The screen has 3 different sections, each held down by glue so necessary force is needed. First remove the acrylic backing that supports the screen and then the main part of the screen. The last thing to remove is the paper-thin cover.

  6. 5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply pull them off. 5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply pull them off. 5.    Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply pull them off.
    • 5. Removing the touchpad is easy and simple as there are layered parts on top of each other, just simply pull them off.

  7. 6.    Finally you should have the ipod dismantelled and you should be able to put the ipod back together.
    • 6. Finally you should have the ipod dismantelled and you should be able to put the ipod back together.

Craig Lawrence

メンバー登録日: 2010年03月11日

444 ポイント

1ガイドが承認済み

5 件のコメント

when i put the rear cover back on, the charging station doesn't line up correctly and the charging station sticks out a bit. any advice?

krnchang - 返信

is the batter swollen

Derek King - 返信

Yes, happened to a Zune 80 I have

Crazyblocks Technologies -

Thank you for this - took the fear factor out of changing battery on my much loved Nano!

jimbradshaw - 返信

It’s extremely hard to connect LCD and Button cables. I screwed it up while reconnecting the cables. IF, you want to disassemble this machine by fun, don’t ever try it.

Sizun Cho - 返信

コメントを追加

統計データを表示:

過去 24時間: 2

過去 7 日: 32

過去 30 日: 135

今までの合計 22,919