修理を始めるには

修理する権利

ストア

Sony Xperia Z5 Teardown

作成者： Lenka (そして 3 人のその他投稿者)
公開日: November 6, 2015
  • コメント: 26
  • お気に入り: 30
  • 閲覧数： 123.5000

分解

この分解で使用される工具

これらのツールを購入する

ビデオの概要

はじめに

This guides will show you how to disassemble Sony Xperia Z5.

この分解は修理ガイドでは ありません。 お持ちのSony Xperia Z5を修理する際は、iFixitの修理ガイドをご利用ください。

  1. Remove SIM card tray. Remove SIM card tray.

    • Remove SIM card tray.

    編集

  2. Heat the back cover to soften the adhesive. Place the suction cup and insert metal opening tool to open a gap from top side.

    • Heat the back cover to soften the adhesive.

    • Place the suction cup and insert metal opening tool to open a gap from top side.

    編集

  3. Insert the guitar picks and slide it to cut the adhesive underneath. Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft. Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft.

    • Insert the guitar picks and slide it to cut the adhesive underneath.

    • Remove back cover. The back cover is glass, so only use a sucker if you're experienced. otherwise use a small blade to lift off the back while the glue is soft.

    編集

  4. Release battery connector and pull off the adhesive tape underneath. Pry up battery. Pry up battery.

    • Release battery connector and pull off the adhesive tape underneath.

    • Pry up battery.

    編集

  5. Release rear camera connector, front camera connector, audio jack flex connector and main flex connector on the motherboard and remove the screws there. Take away the plastic bracket. Take away the plastic bracket.

    • Release rear camera connector, front camera connector, audio jack flex connector and main flex connector on the motherboard and remove the screws there.

    • Take away the plastic bracket.

    編集

  6. Remove metal cover securing loudspeaker and twist off screws. Pry up and loosen the bottom side of main flex assembly. Pry up and loosen the bottom side of main flex assembly.

    • Remove metal cover securing loudspeaker and twist off screws.

    • Pry up and loosen the bottom side of main flex assembly.

    編集

  7. 今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

    今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

  8. Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it) Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it)

    • Remove main flex. ( Attention: the fingerprint sensor connector is here, be careful to loosen it)

    編集

  9. This is main flex assembly. (It comes with loudspeaker and vibration motor ) This is main flex assembly. (It comes with loudspeaker and vibration motor )

    • This is main flex assembly. (It comes with loudspeaker and vibration motor )

    編集

  10. Remove rear camera. Remove rear camera.

    • Remove rear camera.

    編集

  11. Remove that securing bracket, then remove front camera. Remove that securing bracket, then remove front camera. Remove that securing bracket, then remove front camera.

    • Remove that securing bracket, then remove front camera.

    編集

  12. Release connectors on the motherboard. Remove motherboard. Remove motherboard.

    • Release connectors on the motherboard.

    • Remove motherboard.

    編集

  13. Remover cover bracket on the audio jack. Cut adhesive at the top of the audio jack and noise canceling mic, then remove it. Cut adhesive at the top of the audio jack and noise canceling mic, then remove it.

    • Remover cover bracket on the audio jack.

    • Cut adhesive at the top of the audio jack and noise canceling mic, then remove it.

    編集

  14. This is audio jack flex coming with noise canceling mic.

    • This is audio jack flex coming with noise canceling mic.

    編集

  15. Cut the adhesive underneath the earpiece and remove the earpiece. Cut the adhesive underneath the earpiece and remove the earpiece. Cut the adhesive underneath the earpiece and remove the earpiece.

    • Cut the adhesive underneath the earpiece and remove the earpiece.

    編集

  16. Push the charging port flex out of the slot and remove it. Push the charging port flex out of the slot and remove it. Push the charging port flex out of the slot and remove it.

    • Push the charging port flex out of the slot and remove it.

    編集

  17. Remove the microphone. Remove the microphone. Remove the microphone.

    • Remove the microphone.

    編集

  18. Done.

    • Done.

    編集

作成者

3他の投稿者と一緒に

Lenka

メンバー登録日: 2015年11月06日

2,298 ポイント

6のガイドは作成済み

バッジ: 13

+10 個以上のバッジ

23 件のコメント

コメントを追加

No Service after a tear down. What is the problem?

Yuhao Min - 返信

it is hard to define which part causes such problem. Make sure the signal antenna connects with logic board perfectly.

Witrigs -

Would the water proof go out because of the removal/teardown ?

Tam Alden - 返信

Most likely. The back is glued on so unless you can make that seal perfect again, the phone wont be water proof.

Discalimer: I don't own a z5 and have never taken one apart but I have dissasembled my z3 to replace the screen and they look very similar.

Kip K -

Hi Lenka,

short question was that a normal xperia z5 or the dual SIM Version because it looks like the SIM reader is long enough to Support two SIM cards. It would be nice if you could check if there are two SIM ports here.

Tobias K - 返信

コメントを追加

統計データを表示:

過去 24時間: 23

過去 7 日: 156

過去 30 日: 691

今までの合計 123,554