メインコンテンツにスキップ

必要な工具と部品

この分解は修理ガイドでは ありません。 お持ちのSony SRS-X3を修理する際は、iFixitの修理ガイドをご利用ください。

  1. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown, Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 1、 2の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown, Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 1、 2の画像 2
    • There are 6 screws under the rubber feet on the bottom. Removing them allows the bottom plate to be removed, and then from there, the front panel, front cover, and battery compartment.

    • if you need higher reslution photos please leave a comment.

  2. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 2、 3の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 2、 3の画像 2 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 2、 3の画像 3
    • Photos of the Main PCB. IC part numbers can be read off the photos.

    • DC to DC power supply and Yamaha audio amp chip/output filter inductors are the main parts of this side

  3. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 3、 3の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 3、 3の画像 2 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 3、 3の画像 3
    • More images of the main board assembly.

    • The pinouts of the main flex are actually stated on the board which is a huge plus.

    • A CSR Bluetooth SoC and MXIC flash are provided.

  4. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 4、 2の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 4、 2の画像 2
    • The battery pack is on a connector and can be removed before all of this is taken out.

    • Battery is a 2 cell 18650 pack with protection built in; 7.4V

  5. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 5、 2の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 5、 2の画像 2
    • Two 7W speakers with strong magnets are included in this speaker; it is marketed with a 20W power output. Excursion is about 7-10mm at its peak.

  6. Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 6、 2の画像 1 Sony SRS-X3 Bluetooth NFC Wireless Speaker Teardown: 手順 6、 2の画像 2
    • Two passive radiators are present inside the device. They're fairly heavy but rubberized, and they resonate and are tuned for low frequency reproduction. These move a LOT when it's playing. 7-10mm per side.

作成者

3人の作成者と共同で作成されました。

Larry Chen

メンバー登録日: 04/22/13

913 ポイント

5のガイドは作成済み

10 件のコメント

This is great, thank you Larry. I'd wondered about the possibility of upgrading the battery to one that lasts longer between charges but I had no idea how to open the case. It didn't occur to me that the screws would be under the rubber feet!

Steve MacDonald - 返信

Dear Larry, can you give me capture specific card power close to battery. Because i got resistor blown in that card, and i don't know specific value of this resistor. Many Thanks in advance

didi - 返信

One speaker started to give a lot of distortion making it unusable. Repositioned speaker in the heavy (magnet) housing and it's all good again.

Thank you for the opening tips and pics!

Albert - 返信

Larry,

My mini connector for dc into the board has broken. Replace connector or the whole Board? Where can I get a Power Board?

michael ruse - 返信

Where could I find the replacement speaker? My right speaker is buzzing a little on certain songs. Thanks!

Aaron Todd - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 8

過去 30 日: 34

今までの合計 8,521