メインコンテンツにスキップ

この分解で使用される工具

はじめに

I've found a vacuum in my utility room. Since I almost never use it, I thought it was a good idea to see how it works... So let's go!!

この分解は修理ガイドでは ありません。 お持ちのRowenta AC6221を修理する際は、iFixitの修理ガイドをご利用ください。

  1. The 4.8 Rowenta vacuum can be used  for a variety of purposes. It is charged through its pedestal. The power of the pedestal is: Input: 230V - 50 Hz - 7W (AC)
    • The 4.8 Rowenta vacuum can be used for a variety of purposes.

    • It is charged through its pedestal. The power of the pedestal is:

    • Input: 230V - 50 Hz - 7W (AC)

    • Output: 7.5V - 300 mA (DC)

  2. This vacuum has several parts: The tip The reservoir which holds the dust and debris
    • This vacuum has several parts:

    • The tip

    • The reservoir which holds the dust and debris

    • The engine (4.8V)

    • The pedestal

    • The power supply

    • From top to bottom, the reservoir contains 3 parts: the housing, container, and filter.

  3. Remove the two outer Philips #00 screws from the bottom of the engine. The back of the circuit board will now be visible. The back of the circuit board will now be visible.
    • Remove the two outer Philips #00 screws from the bottom of the engine.

    • The back of the circuit board will now be visible.

  4. Remove the two inner screws. Insert a flat screwdriver between the cover and the base of the engine and remove the cover. Insert a flat screwdriver between the cover and the base of the engine and remove the cover.
    • Remove the two inner screws.

    • Insert a flat screwdriver between the cover and the base of the engine and remove the cover.

  5. Apple Watch キット

    Screen and battery repairs just got easier.

    ショップを見る

    Apple Watch キット

    Screen and battery repairs just got easier.

    ショップを見る
    • The wires of the vacuum are now visible.

  6. The wires of the vacuum are now visible. The wires connect the charger light, switch,engine, and power wires.
    • The wires of the vacuum are now visible.

    • The wires connect the charger light, switch,engine, and power wires.

    • The green box labels the engine.

    • The orange box labels one of the four batteries (4*1.2V)

  7. The top of the circuit board contains components including capacitors, resistors, wires, and a chip. The bottom side shows the tracks that connect the components.
    • The top of the circuit board contains components including capacitors, resistors, wires, and a chip.

    • The bottom side shows the tracks that connect the components.

  8. Remove the screw securing the handle with a screwdriver. Open the handle to see the inside using the flat screwdriver.
    • Remove the screw securing the handle with a screwdriver.

    • Open the handle to see the inside using the flat screwdriver.

    • Warning: The handle is difficult to open

    • Warning: In this procedure, the handle was not opened to keep the vacuum intact.

  9. This is the pedestal that will be torn down.
    • This is the pedestal that will be torn down.

  10. At the bottom of the pedestal, remove the 4 rubber pieces. Note: This step provides access to 4 Philips screws. Remove screws using a screwdriver.
    • At the bottom of the pedestal, remove the 4 rubber pieces.

    • Note: This step provides access to 4 Philips screws.

    • Remove screws using a screwdriver.

  11. Lift the plastic piece carefully from the bottom of the pedestal.
    • Lift the plastic piece carefully from the bottom of the pedestal.

  12. Inside the pedestal, the power cable separates into 2 wires. Each wire is connected to a conductive piece.
    • Inside the pedestal, the power cable separates into 2 wires. Each wire is connected to a conductive piece.

    • This completes the vacum cleaner teardown

Bob

メンバー登録日: 2010年04月17日

718 ポイント

3のガイドは作成済み

コメント1件

This could use some discussion of how to replace the rechargeable batteries used in portable vacuum cleaners.

Wayne Seltzer - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 6

過去 30 日: 26

今までの合計 5,955