はじめに

Going to take apart my Power Mac 8600/250!

Tools:

#1 Phillips screwdriver

Spudger/Flathead screwdriver

Your hands!

この分解は修理ガイドでは ありません。 お持ちのPower Macintosh 8600(250)を修理する際は、iFixitの修理ガイドをご利用ください。

There she is! i'm missing the bezel around the floppy drive :(
  • There she is! i'm missing the bezel around the floppy drive :(

コメントを追加する

Start by pressing the big green button. And pulling the door away and up from the computer. And on the Back of the door is the fan. And on the Back of the door is the fan.
  • Start by pressing the big green button. And pulling the door away and up from the computer.

  • And on the Back of the door is the fan.

コメントを追加する

Now it's best to lay the computer flat. And to flip up the tabs, grab the handle and open. And to flip up the tabs, grab the handle and open.
  • Now it's best to lay the computer flat.

  • And to flip up the tabs, grab the handle and open.

コメントを追加する

The innards, motherboard, daughter board, RAM and so fourth.
  • The innards, motherboard, daughter board, RAM and so fourth.

コメントを追加する

Now the speaker Remove the speaker wires And the fan wires from the motherboard
  • Now the speaker

  • Remove the speaker wires

  • And the fan wires from the motherboard

  • Push in the two plastic tabs on either side and lift the speaker up and out.

コメントを追加する

The PRAM battery! Remove the housing by pulling it out and then take the battery out.
  • The PRAM battery!

  • Remove the housing by pulling it out and then take the battery out.

コメントを追加する

The processor, firmly grasp and pull out. Remove the 4 #1 Phillips screws And push the 4 tabs off of the board
  • The processor, firmly grasp and pull out.

  • Remove the 4 #1 Phillips screws

  • And push the 4 tabs off of the board

High failure rate - these bassas’

Mal - 返信

Any video card or usb card, mine happens to be an ethernet 10/100 card.
  • Any video card or usb card, mine happens to be an ethernet 10/100 card.

  • Unfortunately there are 6 spaces but only 3 slots on the motherboard :(

  • Remove the #1 Phillips screw and pull the card out.

コメントを追加する

RAM and VRAM slots!
  • RAM and VRAM slots!

コメントを追加する

Moving on to the CD, ZIP, and Floppy drives (best to close computer now) Remove the bezels and if I had the top one remove that too. Remove the 6 phillips screws and pull the metal frames out.
  • Moving on to the CD, ZIP, and Floppy drives (best to close computer now)

  • Remove the bezels and if I had the top one remove that too.

  • Remove the 6 phillips screws and pull the metal frames out.

コメントを追加する

Remove the data and power cables Pay special attention to this one, it has a clip on it, it helps to use a flathead or a spudger. Pull the drives out of the bay.
  • Remove the data and power cables

  • Pay special attention to this one, it has a clip on it, it helps to use a flathead or a spudger.

  • Pull the drives out of the bay.

コメントを追加する

Now the hard drive. Remove the two phillips screws
  • Now the hard drive.

  • Remove the two phillips screws

  • And the data and power cables (might help to remove them as you pull the drive out)

コメントを追加する

The power source Remove the two connectors There is a clip holding the wires in place. Separate and remove the wires. (both sets)
  • The power source

  • Remove the two connectors

  • There is a clip holding the wires in place. Separate and remove the wires. (both sets)

コメントを追加する

Now remove the 4 phillips screws (it's best to start with the bottom two) And pull it out while de-threading the wires. And pull it out while de-threading the wires.
  • Now remove the 4 phillips screws (it's best to start with the bottom two)

  • And pull it out while de-threading the wires.

コメントを追加する

Plague

メンバー登録日: 2010年06月14日

151 ポイント

1ガイドが承認済み

コメント1件

Nice. I got a beige G3 300 Mhz, the case is similar. Maybe I could also make a teardown.

Nicolas Zbinden - 返信

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 10

過去 30 日: 30

今までの合計 13,179