メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

この分解は修理ガイドでは ありません。 お持ちのNokia E61iを修理する際は、iFixitの修理ガイドをご利用ください。

  1. この手順は未翻訳です。 翻訳を手伝う。

    To access the battery you must remove the back cover. Press the tab on the bottom of the cover in so that the back cover plate can slide over it. Now slide the back cover off of the phone.
    • To access the battery you must remove the back cover. Press the tab on the bottom of the cover in so that the back cover plate can slide over it.

    • Now slide the back cover off of the phone.

  2. この手順は未翻訳です。 翻訳を手伝う。

    Once the backplate is removed, look to the bottom-left corner of the phone where there is a spot to remove the battery.
    • Once the backplate is removed, look to the bottom-left corner of the phone where there is a spot to remove the battery.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Use your finger to lift the battery out.
    • Use your finger to lift the battery out.

    • The E61i uses a Nokia BP-4L standard battery.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Remove the four screws securing the front cover to the rest of the phone using a T7 screwdriver. Remove the four screws securing the front cover to the rest of the phone using a T7 screwdriver.
    • Remove the four screws securing the front cover to the rest of the phone using a T7 screwdriver.

  5. この手順は未翻訳です。 翻訳を手伝う。

    After the screws have been removed, there is nothing else securing the front cover to the rest of the phone. Simply remove the cover by pulling it up and off.
    • After the screws have been removed, there is nothing else securing the front cover to the rest of the phone. Simply remove the cover by pulling it up and off.

  6. この手順は未翻訳です。 翻訳を手伝う。

    Once the front cover has been removed, there is nothing holding the keyboard to the rest of the phone. Simply remove the keyboard from the cover by lifting the keyboard from its interior side.
    • Once the front cover has been removed, there is nothing holding the keyboard to the rest of the phone. Simply remove the keyboard from the cover by lifting the keyboard from its interior side.

  7. この手順は未翻訳です。 翻訳を手伝う。

    After taking off the casing and keyboard, remove the screws holding the screen in place. Use a T-6 for the screws in the middle of the red circles, and use a T-5 for the screw in the middle of the red square. Lift the ribbon off of the contact with the motherboard.
    • After taking off the casing and keyboard, remove the screws holding the screen in place. Use a T-6 for the screws in the middle of the red circles, and use a T-5 for the screw in the middle of the red square.

    • Lift the ribbon off of the contact with the motherboard.

    • When reassembling, firmly press the contacts into place to connect the ribbon and the motherboard.

  8. この手順は未翻訳です。 翻訳を手伝う。

    Once the screws are out, gently pull the screen off of the phone. Be sure not to rip the sticker (in the blue square) that attaches the display and the motherboard.
    • Once the screws are out, gently pull the screen off of the phone.

    • Be sure not to rip the sticker (in the blue square) that attaches the display and the motherboard.

    • Finally, pull the silver case off to completely free the cracked or damaged screen.

  9. この手順は未翻訳です。 翻訳を手伝う。

    Remove the speaker by pulling it off of the display frame. The speaker is connected to the display frame by a ring of adhesive foam (visible in second picture). By removing the speaker, this foam is torn. However, the speaker sticks quite well to the frame without reapplication of any adhesive.
    • Remove the speaker by pulling it off of the display frame.

    • The speaker is connected to the display frame by a ring of adhesive foam (visible in second picture). By removing the speaker, this foam is torn. However, the speaker sticks quite well to the frame without reapplication of any adhesive.

  10. この手順は未翻訳です。 翻訳を手伝う。

    Finally, after the screen and keyboard have been taken off, there is nothing securing the logic board to the rest of the phone. Simply pull the green logic board from the back casing. Once free from the back of the phone, the logic board can be replaced by a new one. Once free from the back of the phone, the logic board can be replaced by a new one.
    • Finally, after the screen and keyboard have been taken off, there is nothing securing the logic board to the rest of the phone. Simply pull the green logic board from the back casing.

    • Once free from the back of the phone, the logic board can be replaced by a new one.

  11. この手順は未翻訳です。 翻訳を手伝う。

    After the logic board has been removed, there is nothing else securing the antenna to the back cover. Simply remove the antenna by pushing outward from the interior side. After the logic board has been removed, there is nothing else securing the antenna to the back cover. Simply remove the antenna by pushing outward from the interior side.
    • After the logic board has been removed, there is nothing else securing the antenna to the back cover. Simply remove the antenna by pushing outward from the interior side.

  12. この手順は未翻訳です。 翻訳を手伝う。

    The volume control buttons are secured to the frame only by their fit around a small piece of the plastic. Using a small flat-head screwdriver or other flat object, lift the ribbon over this piece of the cover.
    • The volume control buttons are secured to the frame only by their fit around a small piece of the plastic. Using a small flat-head screwdriver or other flat object, lift the ribbon over this piece of the cover.

  13. この手順は未翻訳です。 翻訳を手伝う。

    Next, remove the volume control buttons from the cover by pushing or pulling them out away from the interior of the cover.
    • Next, remove the volume control buttons from the cover by pushing or pulling them out away from the interior of the cover.

  14. この手順は未翻訳です。 翻訳を手伝う。

    With the back panel, you will slowly take the Connector Housing by first pushing and sliding it off the back panel.
    • With the back panel, you will slowly take the Connector Housing by first pushing and sliding it off the back panel.

    • *Notice* Be very careful not to lose the small loose spring from behind the button or the small buttton itself. So do this step slowly.

  15. この手順は未翻訳です。 翻訳を手伝う。

    After the Connector Housing has been removed, there is nothing else holding the Microphone in place. Simply remove if from the housing by pulling up.
    • After the Connector Housing has been removed, there is nothing else holding the Microphone in place. Simply remove if from the housing by pulling up.

  16. この手順は未翻訳です。 翻訳を手伝う。

    After the Connector Housing has been removed, there is nothing else holding the Headset Jack in place. Simply remove if from the housing by pulling up.
    • After the Connector Housing has been removed, there is nothing else holding the Headset Jack in place. Simply remove if from the housing by pulling up.

    • EDIT: The connection socket shown in the red square is actually the POWER IN socket.

Christopher Patton

メンバー登録日: 2011年04月07日

208 ポイント

12のガイドは作成済み

チーム

Cal Poly, Team 9-63, Walters Spring 2011 Cal Poly, Team 9-63, Walters Spring 2011人のメンバー

CPSU-WALTERS-S11S9G63

5 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 23

今までの合計 7,307