メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

A teardown of the Nikon Coolpix 3500.

この分解は修理ガイドでは ありません。 お持ちのNikon Coolpix 3500を修理する際は、iFixitの修理ガイドをご利用ください。

  1. Remove the battery cover.
    • Remove the battery cover.

    • Remove the battery.

  2. Remove two 4.5 mm screws next to the battery slot.
    • Remove two 4.5 mm screws next to the battery slot.

    • Remove one 3 mm screw above the CF memory card slot.

    • Remove one 4.5 mm screw next to the CF memory card slot.

  3. Remove two 4.5 mm screws from inside the battery slot.
    • Remove two 4.5 mm screws from inside the battery slot.

  4. Remove two 5 mm screws from the opposite end of the battery slot.
    • Remove two 5 mm screws from the opposite end of the battery slot.

  5. Remove the plastic cap and the 5 mm screw underneath.
    • Remove the plastic cap and the 5 mm screw underneath.

  6. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  7. Remove the five 3.5 mm screws from the bottom of the camera.
    • Remove the five 3.5 mm screws from the bottom of the camera.

    • Gently pry off the grey faceplate.

    • Do not pull hard; there are two wires connecting the faceplate to the motherboard.

  8. Use a spudger to disconnect the white-capped wire at the bottom of the camera. Use a spudger to disconnect the orange-capped wire at the bottom of the camera and set the faceplate aside. Use a spudger to disconnect the orange-capped wire at the bottom of the camera and set the faceplate aside.
    • Use a spudger to disconnect the white-capped wire at the bottom of the camera.

    • Use a spudger to disconnect the orange-capped wire at the bottom of the camera and set the faceplate aside.

  9. Disconnect the grey-capped wires from the motherboard.
    • Disconnect the grey-capped wires from the motherboard.

    • Disconnect the blue wire attached to the green chip from the center of the motherboard.

  10. Remove the 3.5 mm screw from the motherboard next to the rotating lens. Flip the motherboard and lens over to access the three wires on the back that connect to the LED screen.
    • Remove the 3.5 mm screw from the motherboard next to the rotating lens.

    • Flip the motherboard and lens over to access the three wires on the back that connect to the LED screen.

  11. Disconnect the blue wire connecting the motherboard to the LED screen. Disconnect the orange wire using a spudger while pushing out horizontally.
    • Disconnect the blue wire connecting the motherboard to the LED screen.

    • Disconnect the orange wire using a spudger while pushing out horizontally.

    • Disconnect the red capped wire from the motherboard.

    • Lift the motherboard and lens (still connected) out of the back case.

  12. Lift up on the black covering and remove the orange wire connecting the lens to the motherboard.
    • Lift up on the black covering and remove the orange wire connecting the lens to the motherboard.

  13. Remove the 2.5 mm screw next to the red capped wire.
    • Remove the 2.5 mm screw next to the red capped wire.

    • Remove the two 3.4 mm screws on the back of the directional buttons.

    • Remove the two 4.4 mm screws in the metal plate across from the orange wire.

  14. Gently lift the LED screen out of the remaining casing and set it aside. Be careful not to let the rubber backing of the buttons fall out of place.
    • Gently lift the LED screen out of the remaining casing and set it aside.

    • Be careful not to let the rubber backing of the buttons fall out of place.

richard guenther

メンバー登録日: 2010年04月19日

183 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 30-38, Garner Spring 2010 Cal Poly, Team 30-38, Garner Spring 2010人のメンバー

CPSU-GARNER-S10S30G38

5 メンバー

11のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 7,481