メニュー

Your Settings

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

HTC Evo 3D Teardown

作成者： David (そして 3 人のその他投稿者)
公開日: August 23, 2012
  • コメント: 1
  • お気に入り: 50
  • 閲覧数： 18.8k

分解

この分解で使用される工具

これらのツールを購入する

はじめに

This is only a simple teardown to take out all components that can be easily switched out.

この分解は修理ガイドでは ありません。 お持ちのHTC Evo 3Dを修理する際は、iFixitの修理ガイドをご利用ください。

  1. First things first, Remove the back cover, battery and SD card.

    • First things first, Remove the back cover, battery and SD card.

    翻訳

  2. Remove the four T5 Torx screws.

    • Remove the four T5 Torx screws.

    • Then remove the two Phillips screws.

    • *Very sorry for dark image*

    翻訳

  3. Once the screws are all out from the exterior back case, Begin separating the front housing from the back by using a spudger or any similar tool.

    • Once the screws are all out from the exterior back case, Begin separating the front housing from the back by using a spudger or any similar tool.

    • Begin from the bottom were the battery bay is, It is the easiest way.

    • Be careful of ribbons behind the plastic

    翻訳

  4. Free shipping on all orders over $100 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する

  5. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself. Once separated begin to remove the LED board. Apply only light upward force and it will detach itself.

    • Once separated begin to remove the LED board. Apply only light upward force and it will detach itself.

    翻訳

  6. Vibrator come's out easy, Just grab it by the wire and give it a little tug and it should come out. Start unlocking the clips holding the ribbons. pull the white tab up to unlock.

    • Vibrator come's out easy, Just grab it by the wire and give it a little tug and it should come out.

    • Start unlocking the clips holding the ribbons. pull the white tab up to unlock.

    • Example: bottom left is unlocked, bottom right is locked. upper left has bin finished and removed.

    • Tuck the ribbons in without bending or making tears in them.

    翻訳

  7. Behind the main board is two more ribbon's.

    • Behind the main board is two more ribbon's.

    • Flip both tab locks holding the ribbons and they will slide out vary easily, Don't force it.

    • Wifi/cellular antena port, Lift up cord head directly to remove and press straight down centered to put back on.

    • As a side note, the grey tape on the back side of the board was covering the clips so i cut a small section for this guide.

    翻訳

  8. This concludes the (simple) teardown of the Evo 3D.

    • This concludes the (simple) teardown of the Evo 3D.

    翻訳

作成者

3他の投稿者と一緒に

David

メンバー登録日: 2012年03月18日

9,167 ポイント

2のガイドは作成済み

バッジ: 33

+30 個以上のバッジ

チーム

Master Techs Master Techs人のメンバー

Community

281 メンバー

791のガイドは作成済み

コメント1件

コメントを追加

Thanks. This was very helpful.

dano706 - 返信

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 11

今までの合計 18,854