メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

この分解は修理ガイドでは ありません。 お持ちのGarmin Nuvi 200を修理する際は、iFixitの修理ガイドをご利用ください。

  1. この手順は未翻訳です。 翻訳を手伝う。

    Top left: back casing
    • Top left: back casing

    • Top right: front casing

    • Middle left: speaker. Part ($29) and service at portatronics.com

    • Middle right: motherboard

    • Bottom left: battery. Part ($5.20) at amazon.com

    • Bottom right: LCD screen. Assembly kit ($49) at portatronics.com

  2. この手順は未翻訳です。 翻訳を手伝う。

    The Serial Number Strip is at the base of the device. Remove it to two expose two T5 Torx screws. Using the T5 Torx screwdriver, remove the two T5 Torx screws.
    • The Serial Number Strip is at the base of the device. Remove it to two expose two T5 Torx screws.

    • Using the T5 Torx screwdriver, remove the two T5 Torx screws.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Use care. Do no break apart the strip of orange tape that connects the LCD screen and motherboard (red box in third picture.) Using the plastic opening tool, only at the bottom of the device, separate the back panel from the front panel. Using the plastic opening tool, only at the bottom of the device, separate the back panel from the front panel.
    • Use care. Do no break apart the strip of orange tape that connects the LCD screen and motherboard (red box in third picture.)

    • Using the plastic opening tool, only at the bottom of the device, separate the back panel from the front panel.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Use care. The glass on top of the screen is delicate. Using the plastic opening tool, push apart the clasps holding the LCD screen in place.
    • Use care. The glass on top of the screen is delicate.

    • Using the plastic opening tool, push apart the clasps holding the LCD screen in place.

    • Wedge the plastic opening tool between the LCD screen and the metal frame of the device.

  5. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  6. この手順は未翻訳です。 翻訳を手伝う。

    Hold the blue wire from its connector head. Pull the connector head out of the outlet to unplug the speaker.
    • Hold the blue wire from its connector head.

    • Pull the connector head out of the outlet to unplug the speaker.

  7. この手順は未翻訳です。 翻訳を手伝う。

    Using the Phillips #PH00 screwdriver remove the three screws that hold the motherboard in place. Use Screwdriver bit #PH00 in IFixIt's Tool Kit to take out the three screws holding the motherboard in place. Use Screwdriver bit #PH00 in IFixIt's Tool Kit to take out the three screws holding the motherboard in place.
    • Using the Phillips #PH00 screwdriver remove the three screws that hold the motherboard in place.

    • Use Screwdriver bit #PH00 in IFixIt's Tool Kit to take out the three screws holding the motherboard in place.

  8. この手順は未翻訳です。 翻訳を手伝う。

    Peel the strip of orange tape from the white attachment bar on the motherboard. This detaches the motherboard and LCD Screen (see second picture for blue box).
    • Peel the strip of orange tape from the white attachment bar on the motherboard.

    • This detaches the motherboard and LCD Screen (see second picture for blue box).

  9. この手順は未翻訳です。 翻訳を手伝う。

    Remove the strip of orange tape from the LCD screen to detach the LCD screen from the front casing. Remove the strip of orange tape from the LCD screen to detach the LCD screen from the front casing. Remove the strip of orange tape from the LCD screen to detach the LCD screen from the front casing.
    • Remove the strip of orange tape from the LCD screen to detach the LCD screen from the front casing.

  10. この手順は未翻訳です。 翻訳を手伝う。

    Prop the motherboard up. Hold the red and green wires from the connector head. Pull the connector head out of the outlet to detach the motherboard from the back casing.
    • Prop the motherboard up.

    • Hold the red and green wires from the connector head.

    • Pull the connector head out of the outlet to detach the motherboard from the back casing.

  11. この手順は未翻訳です。 翻訳を手伝う。

    Use care. The back casing and battery are glued together. Do not puncture the battery. Push the flat end of the spudger under the battery and separate the battery from the back casing.
    • Use care. The back casing and battery are glued together. Do not puncture the battery.

    • Push the flat end of the spudger under the battery and separate the battery from the back casing.

  12. この手順は未翻訳です。 翻訳を手伝う。

    Using the Phillips #000 screwdriver remove the two screws holding the speaker in place. Remove the speaker.
    • Using the Phillips #000 screwdriver remove the two screws holding the speaker in place.

    • Remove the speaker.

Kasey Gray

メンバー登録日: 2013年10月28日

206 ポイント

1ガイドが承認済み

チーム

University of Maine, Team 1-11, Diaz Fall 2013 University of Maine, Team 1-11, Diaz Fall 2013人のメンバー

UMAINE-DIAZ-F13S1G11

2 メンバー

1のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 2

過去 7 日: 17

過去 30 日: 51

今までの合計 11,252