この分解で使用される工具

はじめに

Free Wheelchair Mission’s most recent model, the GEN 2, was created for use in developing countries. This new model is designed to fit any body type for adults and children with special needs.

The GEN 2 has several updated features for increased safety and maneuverability including: adjustable seating, large caster wheels, extra-thick seat cushion, and adjustable footrests.

In this guide, you will learn how to teardown the GEN 2 wheelchair for storage or transportation.

この分解は修理ガイドでは ありません。 お持ちのGEN 2 Wheelchairを修理する際は、iFixitの修理ガイドをご利用ください。

  1. Find a clean area to work in so every part can be accounted for.
    • Find a clean area to work in so every part can be accounted for.

    コメントを追加する

  2. Remove the footrest by unscrewing the lower bolt, using the 10 mm wrench.
    • Remove the footrest by unscrewing the lower bolt, using the 10 mm wrench.

    • Remove the upper bolt above the socket.

    • Slide out the footrest and unscrew the plate welded to the socket.

    • Slide the plate upward and off of the track to remove.

    • Untie the foot retention belt.

    コメントを追加する

    • Undo the seatbelt.

    • Remove the seat cushion by pulling it off of the velcro.

    • Remove the back padding by untieing the straps attached to the back pad.

    コメントを追加する

    • Turn the wheelchair upside down and untie the plastic seat.

    • Remove the plastic seat support.

    コメントを追加する

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Locate the plastic cap on top of the caster wheels.

    • Place the 10mm wrench underneath the plastic cap and lift it up to remove.

    コメントを追加する

    • Remove the caster wheels by unscrewing the bolt under the cap with a 19 mm wrench.

    • Lift the wheelchair up to pull the caster wheels off.

    • Use caution: The metal sheath and the bearing of the caster wheel is not attached and may fall off upon removal.

    コメントを追加する

    • Use a 1/2 inch socket wrench to unscrew bolts to remove the brakes.

    • Pull the brakes off.

    コメントを追加する

    • Remove the wheels by placing a 19 mm socket wrench on the inside of the wheel and unscrew the bolt.

    • Unscrew the bolt on the outside of the wheel by using a 19 mm socket wrench.

    コメントを追加する

    • Unscrew all of the 10mm bolts on the frame using the 10 mm wrench (15 bolts total).

    • Separate the handle frame pieces from the metal side structure (2 bolts total).

    • Remove the bolts attaching the three support beams (4 bolts each, 12 bolts total).

    Step 9, bullet 4 could use an image of the bolt with the rubber cap.

    Suzanna Schatzlein - 返信

    • Remove the bolt with the rubber cap that attaches the air pump to the center support on the bottom.

    コメントを追加する

    • Congratulations! Your teardown is now complete. Make sure all of the parts are accounted for before storing or shipping.

    コメントを追加する

Jennifer

メンバー登録日: 2013年04月17日

32 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 14-8, Maness Spring 2013 Cal Poly, Team 14-8, Maness Spring 2013人のメンバー

CPSU-MANESS-S13S14G8

5 メンバー

7のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 7

今までの合計 1,764