メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

この分解は修理ガイドでは ありません。 お持ちのApple Studio Display M7649を修理する際は、iFixitの修理ガイドをご利用ください。

  1. この手順は未翻訳です。 翻訳を手伝う。

    The Apple 17" ADC Studio Display The Apple 17" ADC Studio Display
    • The Apple 17" ADC Studio Display

  2. この手順は未翻訳です。 翻訳を手伝う。

    Start by fliping the display so it is face down. Remove these 3 hex screws on the swing arm of the display. Then remove the swing arm, and the piece of plastic underneath it.
    • Start by fliping the display so it is face down.

    • Remove these 3 hex screws on the swing arm of the display.

    • Then remove the swing arm, and the piece of plastic underneath it.

  3. この手順は未翻訳です。 翻訳を手伝う。

    The Swing Arm: The Piece of plastic under the swing arm, you need to remove this(2nd Photo).
    • The Swing Arm:

    • The Piece of plastic under the swing arm, you need to remove this(2nd Photo).

  4. この手順は未翻訳です。 翻訳を手伝う。

    To remove the back panel, remove these hex screws. Then lift the panel from the top of the display. Then lift the panel from the top of the display.
    • To remove the back panel, remove these hex screws.

    • Then lift the panel from the top of the display.

  5. この手順は未翻訳です。 翻訳を手伝う。

    Removing the 2nd panel: Grasp the bottom of the 2nd panel and lift it up, route the ADB cable through the hole. This will reveal a shiney metal panel.
    • Removing the 2nd panel:

    • Grasp the bottom of the 2nd panel and lift it up, route the ADB cable through the hole.

    • This will reveal a shiney metal panel.

    • There may be tape here, remove it.

    • Remove this screw.

  6. この手順は未翻訳です。 翻訳を手伝う。

    Removing the metal shield: After the tape and screw is removed, slide the panel towards you and lift it out. Also, remove the clear USB port cover.
    • Removing the metal shield:

    • After the tape and screw is removed, slide the panel towards you and lift it out.

    • Also, remove the clear USB port cover.

    • We now have full access to the electronics.

  7. 全てのタブを開く

    Mac用RAMアップグレードキット

    キット商品を見る

    どれだけタブを開いても
    十分に足りるRAM容量

    キット商品を見る
  8. この手順は未翻訳です。 翻訳を手伝う。

    To partially free the ADC cable, remove these 6 phillips screws, than remove the metal hinge and the cable elbow.
    • To partially free the ADC cable, remove these 6 phillips screws, than remove the metal hinge and the cable elbow.

  9. この手順は未翻訳です。 翻訳を手伝う。

    Removing the USB Port Assembly:
    • Removing the USB Port Assembly:

    • Remove these 4 phillips screws, and this connector to free the port assembly.

  10. この手順は未翻訳です。 翻訳を手伝う。

    Removing the ADC Cable: Remove these phillips screws.
    • Removing the ADC Cable:

    • Remove these phillips screws.

    • Remove these 3 connectors CareFully!

    • The ADC cable should now be free from the rest of the monitor.

    • Remove this cable as well.

    • The ADC Cable, similar to DVI, provides power, signal, and USB to the display (2nd Photo).

  11. この手順は未翻訳です。 翻訳を手伝う。

    Removing the backlight inverter: Remove these 4 connectors, it is important to remember their order! Remove these 3 phillips screws.
    • Removing the backlight inverter:

    • Remove these 4 connectors, it is important to remember their order!

    • Remove these 3 phillips screws.

  12. この手順は未翻訳です。 翻訳を手伝う。

    Removing the logic board: Remove these two connectors.
    • Removing the logic board:

    • Remove these two connectors.

    • This one too!

  13. この手順は未翻訳です。 翻訳を手伝う。

    Removing the logic board: Remove these 4 phillips screws.
    • Removing the logic board:

    • Remove these 4 phillips screws.

    • This connector isn't used, it is left disconnected, I am assuming that it is to test the display for Apple.

    • Lift the logic board out if the case and set it aside.

  14. この手順は未翻訳です。 翻訳を手伝う。

    Removing the inner rim and button assembly: Using a flathead screwdriver, or spudger, remove the 4 pieces of plastic around the black frame. This will reveal numerous phillips screws.
    • Removing the inner rim and button assembly:

    • Using a flathead screwdriver, or spudger, remove the 4 pieces of plastic around the black frame.

    • This will reveal numerous phillips screws.

    • Remove them all.

  15. この手順は未翻訳です。 翻訳を手伝う。

    Once all of the screws are removed, lift the rim out. Once all of the screws are removed, lift the rim out.
    • Once all of the screws are removed, lift the rim out.

  16. この手順は未翻訳です。 翻訳を手伝う。

    Removing the LCD Panel Remove all of these screws from the metal frame. Remove all of these screws from the metal frame.
    • Removing the LCD Panel

    • Remove all of these screws from the metal frame.

  17. この手順は未翻訳です。 翻訳を手伝う。

    And, all of these:
    • And, all of these:

  18. この手順は未翻訳です。 翻訳を手伝う。

    Once you have removed all of the screws, remove the rear metal panel, watching the inverter cables of course!, this will provide acess to the LCD Panel The Panel is manufactured by Samsung, and aparerntly, aren't easy to find, I Googled the model # and found 2 results. Well, that's it for this teardown, good luck!
    • Once you have removed all of the screws, remove the rear metal panel, watching the inverter cables of course!, this will provide acess to the LCD Panel

    • The Panel is manufactured by Samsung, and aparerntly, aren't easy to find, I Googled the model # and found 2 results.

    • Well, that's it for this teardown, good luck!

  19. この手順は未翻訳です。 翻訳を手伝う。

    My Window-Modded Studio Display
    • My Window-Modded Studio Display

    • This is a neat thing to do to your display if you get bored, it doesn't affect function, but looks really cool!

Chris Green

メンバー登録日: 2009年10月11日

34,298 ポイント

45のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

294 メンバー

950のガイドは作成済み

2 件のコメント

I've got to ask. Are my eyes deceiving me, or is there a NEXT cube in the background?

eweonardspock - 返信

No that,s a nextstation

Luke -

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 8

過去 30 日: 29

今までの合計 20,959