メインコンテンツにスキップ

必要な工具と部品

この分解は修理ガイドでは ありません。 お持ちのApple Studio Display M7649を修理する際は、iFixitの修理ガイドをご利用ください。

  1. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 1、 2の画像 1 : 手順 1、 2の画像 2
    • The Apple 17" ADC Studio Display

  2. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 2、 3の画像 1 : 手順 2、 3の画像 2 : 手順 2、 3の画像 3
    • Start by fliping the display so it is face down.

    • Remove these 3 hex screws on the swing arm of the display.

    • Then remove the swing arm, and the piece of plastic underneath it.

  3. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 3、 2の画像 1 : 手順 3、 2の画像 2
    • The Swing Arm:

    • The Piece of plastic under the swing arm, you need to remove this(2nd Photo).

  4. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 4、 3の画像 1 : 手順 4、 3の画像 2 : 手順 4、 3の画像 3
    • To remove the back panel, remove these hex screws.

    • Then lift the panel from the top of the display.

  5. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 5、 3の画像 1 : 手順 5、 3の画像 2 : 手順 5、 3の画像 3
    • Removing the 2nd panel:

    • Grasp the bottom of the 2nd panel and lift it up, route the ADB cable through the hole.

    • This will reveal a shiney metal panel.

    • There may be tape here, remove it.

    • Remove this screw.

  6. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 6、 3の画像 1 : 手順 6、 3の画像 2 : 手順 6、 3の画像 3
    • Removing the metal shield:

    • After the tape and screw is removed, slide the panel towards you and lift it out.

    • Also, remove the clear USB port cover.

    • We now have full access to the electronics.

  7. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 7、 1の画像 1
    • To partially free the ADC cable, remove these 6 phillips screws, than remove the metal hinge and the cable elbow.

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 1の画像 1
    • Removing the USB Port Assembly:

    • Remove these 4 phillips screws, and this connector to free the port assembly.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 2の画像 1 : 手順 9、 2の画像 2
    • Removing the ADC Cable:

    • Remove these phillips screws.

    • Remove these 3 connectors CareFully!

    • The ADC cable should now be free from the rest of the monitor.

    • Remove this cable as well.

    • The ADC Cable, similar to DVI, provides power, signal, and USB to the display (2nd Photo).

  10. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 10、 3の画像 1 : 手順 10、 3の画像 2 : 手順 10、 3の画像 3
    • Removing the backlight inverter:

    • Remove these 4 connectors, it is important to remember their order!

    • Remove these 3 phillips screws.

  11. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 11、 2の画像 1 : 手順 11、 2の画像 2
    • Removing the logic board:

    • Remove these two connectors.

    • This one too!

  12. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 12、 2の画像 1 : 手順 12、 2の画像 2
    • Removing the logic board:

    • Remove these 4 phillips screws.

    • This connector isn't used, it is left disconnected, I am assuming that it is to test the display for Apple.

    • Lift the logic board out if the case and set it aside.

  13. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 13、 3の画像 1 : 手順 13、 3の画像 2 : 手順 13、 3の画像 3
    • Removing the inner rim and button assembly:

    • Using a flathead screwdriver, or spudger, remove the 4 pieces of plastic around the black frame.

    • This will reveal numerous phillips screws.

    • Remove them all.

  14. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 14、 2の画像 1 : 手順 14、 2の画像 2
    • Once all of the screws are removed, lift the rim out.

  15. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 15、 3の画像 1 : 手順 15、 3の画像 2 : 手順 15、 3の画像 3
    • Removing the LCD Panel

    • Remove all of these screws from the metal frame.

  16. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 16、 1の画像 1
    • And, all of these:

  17. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 17、 3の画像 1 : 手順 17、 3の画像 2 : 手順 17、 3の画像 3
    • Once you have removed all of the screws, remove the rear metal panel, watching the inverter cables of course!, this will provide acess to the LCD Panel

    • The Panel is manufactured by Samsung, and aparerntly, aren't easy to find, I Googled the model # and found 2 results.

    • Well, that's it for this teardown, good luck!

  18. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 18、 1の画像 1
    • My Window-Modded Studio Display

    • This is a neat thing to do to your display if you get bored, it doesn't affect function, but looks really cool!

作成者

4人の作成者と共同で作成されました。

Chris Green

メンバー登録日: 10/11/09

36,876 ポイント

49のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

322 メンバー

2,506のガイドは作成済み

2 件のコメント

I've got to ask. Are my eyes deceiving me, or is there a NEXT cube in the background?

eweonardspock - 返信

No that,s a nextstation

Luke -

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 14

過去 30 日: 65

今までの合計 24,534