はじめに

Here you will see a breakdown of the Apple Studio Display M2454. This will be useful in repairing broken or malfunctioning parts in the future.

この分解は修理ガイドでは ありません。 お持ちのApple Studio Display M2454を修理する際は、iFixitの修理ガイドをご利用ください。

Notice that the main components of the monitor are only accessible from the back of the device.
  • Notice that the main components of the monitor are only accessible from the back of the device.

コメントを追加する

Locate the four hex head screws located on the corners of the back panel.
  • Locate the four hex head screws located on the corners of the back panel.

    • Remove the screws with a 2mm hex screwdriver.

コメントを追加する

Remove the clear and gray back panels.
  • Remove the clear and gray back panels.

コメントを追加する

Remove the three screws with #2 phillips head screwdriver.
  • Remove the three screws with #2 phillips head screwdriver.

コメントを追加する

To remove the metal panel, push towards the bottom of the monitor to release its clips and pull the panel away.
  • To remove the metal panel, push towards the bottom of the monitor to release its clips and pull the panel away.

コメントを追加する

Remove screw holding the plastic bracket with #2 Phillips head screwdriver.
  • Remove screw holding the plastic bracket with #2 Phillips head screwdriver.

コメントを追加する

Remove the four screws on the metal bracket.
  • Remove the four screws on the metal bracket.

コメントを追加する

Remove the two philips head hold-down screws with the #2 Phillips head screwdriver.
  • Remove the two philips head hold-down screws with the #2 Phillips head screwdriver.

コメントを追加する

Remove black connector by pushing the end of the tab closest to the wiring and pulling away from board.
  • Remove black connector by pushing the end of the tab closest to the wiring and pulling away from board.

コメントを追加する

Remove white connector by lifting tab and pulling away from board.
  • Remove white connector by lifting tab and pulling away from board.

    • Be careful when lifting tabs, they break easily.

コメントを追加する

Remove connector connected to the hold down previously removed simply by pulling with hand.
  • Remove connector connected to the hold down previously removed simply by pulling with hand.

コメントを追加する

Now that the main computer cable is detached, remove it away from monitor.
  • Now that the main computer cable is detached, remove it away from monitor.

コメントを追加する

Remove the two screws holding the USB port in place with #2 Phillip's head screwdriver.
  • Remove the two screws holding the USB port in place with #2 Phillip's head screwdriver.

コメントを追加する

Remove the screw on the wire hold down with #2 Phillips head screwdriver.
  • Remove the screw on the wire hold down with #2 Phillips head screwdriver.

コメントを追加する

Remove white connector connected to LCD main board by lifting tab with tool and pulling away from board.
  • Remove white connector connected to LCD main board by lifting tab with tool and pulling away from board.

コメントを追加する

The USB port is now detached, remove it from monitor.
  • The USB port is now detached, remove it from monitor.

コメントを追加する

Remove connector on the left bottom corner of the LCD main board by simply pulling with hand.
  • Remove connector on the left bottom corner of the LCD main board by simply pulling with hand.

コメントを追加する

Remove the connector on the bottom right corner by 1st removing tape first and pulling with hand.
  • Remove the connector on the bottom right corner by 1st removing tape first and pulling with hand.

コメントを追加する

Remove top right connector of the LCD main board by pulling with hand.
  • Remove top right connector of the LCD main board by pulling with hand.

コメントを追加する

Remove the final connector of the LCD main board by pulling with hand.
  • Remove the final connector of the LCD main board by pulling with hand.

コメントを追加する

Remove the four screws on each corner of the main board with #2 Phillips head screwdriver.
  • Remove the four screws on each corner of the main board with #2 Phillips head screwdriver.

コメントを追加する

The board is now detached, remove it from monitor.
  • The board is now detached, remove it from monitor.

コメントを追加する

Locate the top and bottom connector on the CCFL inverter and remove it by inserting pin into the small holes and pulling away.
  • Locate the top and bottom connector on the CCFL inverter and remove it by inserting pin into the small holes and pulling away.

    • This step may be easier with two people.

コメントを追加する

Remove the two screws on the top and bottom of the CCFL inverter with #2 Phillips head screwdriver.
  • Remove the two screws on the top and bottom of the CCFL inverter with #2 Phillips head screwdriver.

コメントを追加する

The CCFL inverter is now detached, remove it from monitor.
  • The CCFL inverter is now detached, remove it from monitor.

コメントを追加する

You have now successfully taken apart a Apple Studio Display M2454.
  • You have now successfully taken apart a Apple Studio Display M2454.

コメントを追加する

Dylan Perry

メンバー登録日: 2010年01月20日

129 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 13-27, Maness Winter 2010 Cal Poly, Team 13-27, Maness Winter 2010人のメンバー

CPSU-MANESS-W10S13G27

4 メンバー

5のガイドは作成済み

This model is also known as the Apple Studio Display 15" LCD.

analogcd - 返信

excellent wee guide......i came here in my search for a replacement stand for this model.

bobby nailen - 返信

Failing caps were the main problem with this — no air flow.

Mal - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 10

過去 30 日: 18

今までの合計 5,972