メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 2を翻訳中

手順2
This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue. If you're installing a new front panel assembly, it may need the following preparation:
Front panel preparation
  • This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.

  • If you're installing a new front panel assembly, it may need the following preparation:

  • Peel the large clear plastic liner off of the inside of the glass.

  • Peel any blue plastic backings covering the adhesive around the perimeter of the front panel assembly.

  • Once removed, the adhesive strips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.

  • Don't remove any copper coverings from the outlined region, such as yellow kapton tape or black electrical tape.

  • Ensure the glass panel is free of fingerprints and grime before installing it on your device.

新しいフロントパネルアセンブリに付け替える場合、次の準備が必要です。

正面パネルアセンブリの周囲の接着剤をカバーしているプラスチックストリップを剥がしてください。

デジタイザーケーブルから小さい接着剤シールを取ります。

全ての銅パーツが新しい交換スクリーン上で覆われていることを確認してください。もし覆われていない場合は、スクリーンがばらばらに動いてしまいます。

[*title] Front panel preparation
[* icon_reminder] This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.
[*
icon_note] If you're installing a new front panel assembly, it may'''may''' need the following preparation:
[* red] Peel the large clear plastic stripsliner off of the inside of the glass.
[* orange] Peel any blue plastic backings
covering the adhesive around the perimeter of the front panel assembly.
[* orange] Remove

[* icon_caution] Once removed,
the small piece of adhesive backingstrips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.
[* yellow] '''Don't remove any copper coverings
from the digitizer cableoutlined region''', such as yellow kapton tape or black electrical tape.
[* black] Make sure all copperEnsure the glass panel is coveredfree of fingerprints and grime before installing it on the new replacement screen as once fitted without this the screen will move randomlyyour device.
[*title] Front panel preparation
[* icon_reminder] This is a good time to power on your iPad and test all functions before you seal the display in place. Be sure to power your iPad back down completely before you continue.
[*
icon_note] If you're installing a new front panel assembly, it may'''may''' need the following preparation:
[* red] Peel the large clear plastic stripsliner off of the inside of the glass.
[* orange] Peel any blue plastic backings
covering the adhesive around the perimeter of the front panel assembly.
[* orange] Remove

[* icon_caution] Once removed,
the small piece of adhesive backingstrips will be exposed. Don't remove these backings until you're ready to install the front panel assembly.
[* yellow] '''Don't remove any copper coverings
from the digitizer cableoutlined region''', such as yellow kapton tape or black electrical tape.
[* black] Make sure all copperEnsure the glass panel is coveredfree of fingerprints and grime before installing it on the new replacement screen as once fitted without this the screen will move randomlyyour device.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります