メインコンテンツにスキップ

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 1を翻訳中

手順1
Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive. If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.
  • Opening your phone will compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.

  • If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.

  • Lay the heated iOpener over the rear panel for about two minutes to loosen the adhesive around the edge of the glass.

  • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

  • Shift the iOpener to heat the remaining section of the panel for another two minutes.

  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

電話本体を裏側にします。

ガラスにひびが入っている場合は、取り外し作業の間ガラスを固定する必要があるため、パネル全体に透明の保護テープを貼り付けてください。

ガラスの端にiOpenerを約30秒間置いて、ガラス周辺に付けられた接着剤を柔らかくします。

iOpenerを反対側の端に約30秒間置いて、パネルの残り部分の接着剤も温めます。

[* icon_note] Place theOpening your phone facedownwill compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.
[* icon_note] Place theOpening your phone facedownwill compromise its waterproof seals. Have replacement adhesive ready before you proceed, or take care to avoid liquid exposure if you reassemble your phone without replacing the adhesive.
[* icon_note] If your glass is shattered, put packing tape over the entire panel to hold it together during the removal process.
[* black] Lay the heated iOpener over the rear panel for about 30 secondstwo minutes to loosen the adhesive around the edge of the glass.
[* icon_note] You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

[* black] Shift the iOpener to heat the remaining section of the panel for another 30 secondstwo minutes.
[* icon_caution] A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage
.
[* black] Lay the heated iOpener over the rear panel for about 30 secondstwo minutes to loosen the adhesive around the edge of the glass.
[* icon_note] You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

[* black] Shift the iOpener to heat the remaining section of the panel for another 30 secondstwo minutes.
[* icon_caution] A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage
.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります