Skip to main content

注意:あなたはさきほど閲覧しているガイドの前提となるページを編集しています。あなたが行った変更は、この手順を含むガイド全体に影響を与えます。

英語
日本語

手順 2を翻訳中

手順2
Before you start placing strips, remove all of the old adhesive from around the perimeter of the rear enclosure. If you are re-using your existing display, you must also remove the old adhesive from the back of the display.
  • Before you start placing strips, remove all of the old adhesive from around the perimeter of the rear enclosure.

  • If you are re-using your existing display, you must also remove the old adhesive from the back of the display.

  • Peel off the old strips of adhesive using tweezers or your fingers. Start at the bottom and peel upward towards the top of the device.

  • After all the old adhesive is removed, carefully clean the area under the adhesive with 90% (or greater) isopropyl alcohol and a lint-free cloth. Wipe in one direction, not back and forth.

  • Don't skip this step, or your new adhesive strips may not bond properly, and the display may fall out of your iMac.

ストリップの取り付けを開始する前に、後ろ(本体側)の周りに残っている古い接着剤をすべて取り除いてください。

既存のディスプレイを再使用する場合は、古い接着剤もディスプレイの背面から取り外す必要があります。

ピンセットを使用して、各接着剤ストリップの端をつかみ、はがします。

必要に応じてこのプロセスを繰り返し、古い接着剤をすべて除去します。

必要に応じて、スパッジャー(修理用ツール)を使用して残りの接着剤を掻き取ってから、指ではがしてください。

少量のイソプロピルアルコールと糸くずの出ない布を使用して、少量残った両面テープを拭き取る必要があります。

[* icon_caution] Before you start placing strips, remove all of the old adhesive from around the perimeter of the rear enclosure.
[* black] If you are re-using your existing display, you must also remove the old adhesive from the back of the display.
[* [* black] Use a pairPeel off the old strips of adhesive using tweezers to graspor your fingers. Start at the bottom and peel up''upward'' towards the edgetop of each adhesive strip.
[*
the device.
[*
black] Repeat this process as necessary to removeAfter all of the old adhesive.
[* icon_note] If necessary, use a spudger to scrape up
adhesive is removed, carefully clean the remaining adhesive, then peelarea under the adhesive with your fingers.
[* icon_note] You may need to use a small amount of
90% (or greater) isopropyl alcohol and aa lint-free cloth to wipe away any left over residuecloth. Wipe in one direction, not back and forth.
[* icon_caution] '''Don't skip this step''', or your new adhesive strips may not bond properly, and the display may fall out of your iMac
.
[* [* black] Use a pairPeel off the old strips of adhesive using tweezers to graspor your fingers. Start at the bottom and peel up''upward'' towards the edgetop of each adhesive strip.
[*
the device.
[*
black] Repeat this process as necessary to removeAfter all of the old adhesive.
[* icon_note] If necessary, use a spudger to scrape up
adhesive is removed, carefully clean the remaining adhesive, then peelarea under the adhesive with your fingers.
[* icon_note] You may need to use a small amount of
90% (or greater) isopropyl alcohol and aa lint-free cloth to wipe away any left over residuecloth. Wipe in one direction, not back and forth.
[* icon_caution] '''Don't skip this step''', or your new adhesive strips may not bond properly, and the display may fall out of your iMac
.

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります