メインコンテンツにスキップ

注意:あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての12個のガイドに反映されます。

英語
日本語

手順 2を翻訳中

手順2
Disconnect the camera cable by sliding it horizontally out of its socket. Pull the cable parallel to the surface of the logic board, in the direction of the optical drive. Do not pull straight up, or you will destroy the connector.
  • Disconnect the camera cable by sliding it horizontally out of its socket.

  • Pull the cable parallel to the surface of the logic board, in the direction of the optical drive. Do not pull straight up, or you will destroy the connector.

  • If you see a small plastic retainer stuck to the logic board that prevents the camera cable from sliding out, peel it up carefully from the logic board. Apply a little heat from a hair dryer or heat gun if necessary to help soften the adhesive holding it in place. Do not attempt to forcibly disconnect the cable with the retainer in place.

  • If you still have trouble, use the point of a spudger to push at each side of the connector and "walk" it slowly from its socket.

カメラケーブルの先端をまっすぐにソケットから引いて接続を外します。

小さなハードプラスチップのパーツがロジックボードに取り付けられており、ソケットからカメラケーブルが落ちるのを防いでいます。このパーツをまず取り除いてから作業を進めてください。コネクターにダメージを与えてしまいます。

ロジックボードの表面と並行してコネクターを光学ドライブ側に向けて引っ張ります。ソケットからまっすぐ上に引っ張らないでください。

[* black] Disconnect the camera cable by pulling the male end straight away fromsliding it horizontally out of its socket.
[* icon_caution] There is a small piecePull the cable parallel to the surface of hardthe logic board, in the direction of the optical drive. Do '''not''' pull straight up, or you will destroy the connector.
[* black] If you see a [https://d3nevzfk7ii3be.cloudfront.net/igi/FdbjNAIY4CP3TQZk.full|small
plastic retainer|new_window=true] stuck to the logic board that stopsprevents the camera cable from falling out of its socket. Be sure tosliding out, peel this off first or you could damageit up carefully from the connectors.
[* icon_note] Make sure
logic board. Apply a little heat from a hair dryer or heat gun if necessary to pullhelp soften the connector paralleladhesive holding it in place. '''Do not''' attempt to forcibly disconnect the facecable with the retainer in place.
[* black] If you still have trouble, use the point of a spudger to push at each side
of the logic boardconnector and toward the optical drive, not straight up[guide|25629|"walk" it slowly from its socketsocket|stepid=64975].
[* black] Disconnect the camera cable by pulling the male end straight away fromsliding it horizontally out of its socket.
[* icon_caution] There is a small piecePull the cable parallel to the surface of hardthe logic board, in the direction of the optical drive. Do '''not''' pull straight up, or you will destroy the connector.
[* black] If you see a [https://d3nevzfk7ii3be.cloudfront.net/igi/FdbjNAIY4CP3TQZk.full|small
plastic retainer|new_window=true] stuck to the logic board that stopsprevents the camera cable from falling out of its socket. Be sure tosliding out, peel this off first or you could damageit up carefully from the connectors.
[* icon_note] Make sure
logic board. Apply a little heat from a hair dryer or heat gun if necessary to pullhelp soften the connector paralleladhesive holding it in place. '''Do not''' attempt to forcibly disconnect the facecable with the retainer in place.
[* black] If you still have trouble, use the point of a spudger to push at each side
of the logic boardconnector and toward the optical drive, not straight up[guide|25629|"walk" it slowly from its socketsocket|stepid=64975].

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります