メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

注意:あなたは必要条件ガイドを編集しています。あなたが行なう変更は、この手順を含む全ての2個のガイドに反映されます。

英語
中国語

手順 16を翻訳中

手順16
Test your new battery's fit and alignment carefully before installing it. Unlike most laptop batteries, the MacBook's battery is precisely contoured to fit the "terraced" shape of the lower case. Each cell must be correctly positioned, or the MacBook may not close correctly and damage may result. Your replacement battery may come affixed to a thick plastic top liner to help keep the individual cells in position as you install it. Don't remove this liner until after the battery is installed.
  • Test your new battery's fit and alignment carefully before installing it.

  • Unlike most laptop batteries, the MacBook's battery is precisely contoured to fit the "terraced" shape of the lower case. Each cell must be correctly positioned, or the MacBook may not close correctly and damage may result.

  • Your replacement battery may come affixed to a thick plastic top liner to help keep the individual cells in position as you install it. Don't remove this liner until after the battery is installed.

  • If your battery came with adhesive pre-installed on the bottom, peel away the bottom plastic liner to expose the adhesive. If your battery did not come with adhesive, apply a thin double-sided adhesive tape such as Tesa 61395 to the lower case in the areas marked in red.

  • Carefully position the battery and set it into place. Press and hold each cell firmly for 5-10 seconds to secure it to the lower case. Afterward, peel off the plastic top liner along with any foam padding.

  • 2015 models only: After reassembly, remember to connect your MacBook to low-voltage power before turning it on. Failure to follow these instructions may result in logic board damage.

  • Calibrate your newly installed battery: charge it to 100%, and keep charging it for at least 2 more hours. Unplug and use it normally to drain the battery. When you see the low battery warning, save your work, and keep your laptop on until it goes to sleep due to low battery. Wait at least 5 hours, then charge your laptop uninterrupted to 100%.

  • If you notice any unusual behavior or problems after installing your new battery, you may need to reset your MacBook's SMC.

在安装之前,请仔细测试新电池的安装和对齐情况。

与大多数笔记本电池不同,MacBook的电池外形精确,以适应下壳的“梯形”形状。必须正确定位每个单元格,否则MacBook可能无法正确关闭并可能导致损坏。

你的更换电池可能贴在厚塑料顶部衬垫上,以便在安装时将各个电池保持在适当的位置。

在安装电池之前,请勿卸下此衬管。如果你的电池预装在底部,请剥去底部塑料衬垫以露出粘合剂。如果您的电池没有附带粘合剂,请在标有红色的区域将薄的双面胶带(如Tesa 61395)粘贴到下壳。

小心放置电池并将其放置到位。将每个电池牢牢按住5-10秒钟,将其固定在下壳上。然后,将塑料顶部衬垫与任何泡沫衬垫一起剥离。

仅限2015款:重新组装后,请务必在开机前将MacBook连接至低压电源。不遵守这些说明可能会导致主板损坏。

校准 你新安装的电池: 将电池充电至100%并继续充电至少两小时,然后拔掉电源正常使用你的电脑。当出现低电量警告时,保存你的工作并继续使用电脑直至电量低自动休眠。静置至少5小时后一次性充电至100%。

如果你在安装新电池以后注意到任何异常举动或者问题,也许你需要重置你 MacBook Pro 的 SMC。

クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります