メインコンテンツにスキップ
ドイツ語
英語

Dell c1760nw Clean main mechanics and make it work

ガイド情報

= 完了 = 不完全

      現在取り組み中のこの deviceの特定のパーツやコンポーネントの詳細を記載してください。 例: バッテリー

      タイトルを作成

      この短い1−2文の概要は検索結果に表示されます。

      ガイドの編集に取りかかる前に参考資料に目を通してください。

      ガイドの手順

      手順1 — Remove error 007-371

      Your Dell C1760nw ( and some other LED/laserprinter models) shows you incessantly the error 007-371? Then this repair guide is interesting for you!

      手順2 — Remove the paper tray

      Remove the folding paper pad, by bending it (careful) and unfixing it on one site.

      手順3 — Remove front housing parts

      Remove the bar at the top and the front.

      手順4 — Remove TopCase

      Remove two srews from the front. And to take off the cover leverage remove the tabs diagonally from the front over the latching.

      手順5 — Continued: Remove TopCase

      Carefully lift the cover (Attention: cable connection to the display is hanging there) and rack it to the back of the printer (move it back and forth to unhook the locking nipple): unplug the display connector (yellow lines) from the I/O board, unroute the cable and remove the cover.

      手順6 — Remove left housing part

      Place the printer on the right side and remove the left side panel (there are 2 lugs under the printer)

      手順7 — Next: Remove the left housing part

      Reposition the printer and hold the disengaged lugs in the disengaged position. Open the rear flap and slide the side panel backwards while moving away from the printer.

      手順8 — Remove the WLAN card

      The WLAN card is secured with a screw-> remove it, carefully unplug the WLAN card and remove the WLAN bracket together with the cable

      手順9 — Remove I / O card

      Loosen all connectors (pull plugs carefully out of sockets)

      手順10 — Remove metal plate (beneath I / O card)

      The metal plate under the I/O card (which holds the I/O card) is secured with 3 screws. Remove all 3 screws

      手順11 — Remove the fan

      The fan is secured to this plate with a screw (red arrow): Loosen the screw and unlock the locking device on the other side of the fan.

      手順12 — Unroute wiring harnesses

      Unroute all cable harnesses on the left side from the guides.

      手順13 — Remove other components

      A) Remove plastic bracket with gear for paper feed (2 screws) - No photo!

      手順14 — B) Remove main drive

      Loosen 4 screws

      手順15 — C) Remove board with color control

      Carefully pull the upper flexible cable out of the base

      手順16 — Remove the color control gear

      Next, we remove the color control gear (black, large plastic bracket with 15 meshing gears (5 screws have to be loosened).

      手順17 — Washing the gearwheels ...

      Washing the gearwheels.

      手順18 — First success

      The "before / after" evidence ;-)

      手順19 — Second success

      And once again: before and after

      手順20 — Clean the chassis

      Now the chassis should be cleaned (only for the good feeling! and because of the care...)

      手順21 — After assembly

      The assembly is done in reverse order... Until the printer only needs the right and front housing part plus the paper flap.

      クリエイティブコモンズのオープンソース著作権のもと、あなたの投稿は著作権の対象となります