メインコンテンツにスキップ

このバージョンは誤った内容を含んでいる可能性があります。最新の承認済みスナップショットに切り替えてください。

必要な工具と部品

  1. , サイドブラシ: 手順 1、 1の画像 1
    • ルンバを裏返して、底側を上向きにします。

  2. : 手順 2、 1の画像 1
    • サイドブラシを固定しながら、#1プラスドライバーを使って、4.5mmネジをブラシの中央から外します。

  3. : 手順 3、 1の画像 1
    • ゆっくりとブラシを上向きに引っ張り、取り出します。

  4. , iRobot ルンバ 551 下部プレートの解体方法: 手順 4、 1の画像 1
    • ルンバを裏返して、そこ側を上向きに配置します。

  5. : 手順 5、 2の画像 1 : 手順 5、 2の画像 2
    • #2 プラスドライバーを使って、下部プレートを固定している拘束ネジを外します。

  6. : 手順 6、 1の画像 1
    • 慎重に下部プレートを持ち上げます。

    • バッテリーは底部プレートによって固定されています。そのため、下部プレートを取り外すと、バッテリーが落下することがあります。

  7. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 7、 3の画像 1 : 手順 7、 3の画像 2 : 手順 7、 3の画像 3
    • With a Phillips #1 screwdriver, remove the ten 12mm screws located along the bottom of the bumper.

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 1の画像 1
    • Lift the bottom cover and set it to the side.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 2の画像 1 : 手順 9、 2の画像 2
    • Flip the Roomba over, grasp the bumper, and gently lift to remove.

    • The battery is not secured in place once the bottom plate has been removed, and may fall out when the Roomba is turned right-side up.

  10. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 10、 1の画像 1
    • Flip the Roomba so that the bottom is facing you.

  11. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 11、 2の画像 1 : 手順 11、 2の画像 2
    • Remove the two 5mm screws located near the center of the bumper using a Phillips #1 screwdriver.

  12. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 12、 1の画像 1
    • Pull gently on the bottom of the sensor to remove.

  13. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 13、 3の画像 1 : 手順 13、 3の画像 2 : 手順 13、 3の画像 3
    • Flip the bumper over and lift the sensor from its compartment.

    • You are now free to replace the bumper sensor.

ゴール

4 の人々がこのガイドを完成させました。

作成者

3人の作成者と共同で作成されました。

Cody Rhoads

メンバー登録日: 01/16/14

348 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 13-14, Regan Winter 2014 Cal Poly, Team 13-14, Regan Winter 2014人のメンバー

CPSU-REGAN-W14S13G14

4 メンバー

19のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 7

過去 30 日: 16

今までの合計 4,668