修理を始めるには

修理する権利

パーツ＆ツール

iPod Touch 1st Generation Case Replacement

作成者： Miroslav Djuric (そして 4 人のその他投稿者)
  • コメント: 9
  • お気に入り: 0
  • 完了: 2

難易度

難しい

手順

4

所要時間

必要時間を提案??

セクション

1

フラグ

1

Prerequisite Only

必要条件のみ

このガイドは他のガイドにとって唯一の必要条件であることに注意してください。

はじめに

This guide shows how to open the iPod Touch 1st Generation's case.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Opening the case is a tough and potentially dangerous task. A good amount of force is required to wedge the plastic opening tool in between the case seams. The case may be damaged if this step is not done properly. Make sure not to hurt yourself while opening your iPod.

    • Opening the case is a tough and potentially dangerous task. A good amount of force is required to wedge the plastic opening tool in between the case seams. The case may be damaged if this step is not done properly. Make sure not to hurt yourself while opening your iPod.

    • Insert the small plastic opening tool into the seam in between plastic display panel and the metal back panel. The angled edge should point towards the metal back panel.

    • Hold the tool in place once it is wedged inside and the two panels are separated.

    翻訳

  2. There are seven interlocking retaining clips on each side of the iPod. The large plastic opening tool will be used to separate the front panel from the metal back of the iPod. Insert the large opening tool into the right side of the iPod, with the edge of the tool pointing towards the metal back. Gently enlarge the existing crevice by wiggling the large opening tool and moving it to the right.

    • There are seven interlocking retaining clips on each side of the iPod. The large plastic opening tool will be used to separate the front panel from the metal back of the iPod.

    • Insert the large opening tool into the right side of the iPod, with the edge of the tool pointing towards the metal back.

    • Gently enlarge the existing crevice by wiggling the large opening tool and moving it to the right.

    • Continue doing so until the right side of the iPod is loose.

    翻訳

  3. iPhone LCDスクリーン修理キット

    生涯保証付きの低コストオプション

    キット商品を見る

    iPhone LCDスクリーン修理キット

    品質ではなく、修理コストを削減しましょう。

    キット商品を見る

  4. Switch to the other side of the iPod. Follow the same procedure as in the previous step to release the seven clips holding the panels in place. Once the panels are separated on this side, the back panel can be separated from the rest of the iPod.

    • Switch to the other side of the iPod.

    • Follow the same procedure as in the previous step to release the seven clips holding the panels in place.

    • Once the panels are separated on this side, the back panel can be separated from the rest of the iPod.

    翻訳

  5. Gently lift the rear panel using your fingers. The front and back of the iPod should now be completely separated. The gold antenna (third picture) can easily fall out from its housing. Make sure that the antenna is securely in place before closing the iPod.

    • Gently lift the rear panel using your fingers.

    • The front and back of the iPod should now be completely separated.

    • The gold antenna (third picture) can easily fall out from its housing. Make sure that the antenna is securely in place before closing the iPod.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

4他の投稿者と一緒に

Miroslav Djuric

149,825 ポイント

143のガイドは作成済み

バッジ: 54

+51 個以上のバッジ

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 9,520