Fix Your Stuff

Right to Repair

Parts & Tools

iPod Nano 7th Generation Bluetooth Antenna Replacement

作成者： Sam Goldheart (そして 3 人のその他投稿者)
  • コメント: 51
  • お気に入り: 4
  • 完了: 2

難易度

普通

手順

19

所要時間

必要時間を提案??

セクション

3

フラグ

0

はじめに

This guide will walk you through the instructions for replacing the Bluetooth antenna on a 7th Gen iPod Nano.

  1. We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener. Place the iOpener in the center of the microwave.

    • We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

    • Place the iOpener in the center of the microwave.

    • For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

    編集

  2. Heat the iOpener for thirty seconds.

    • Heat the iOpener for thirty seconds.

    • Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.

    • Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.

    • Never touch the iOpener if it appears swollen.

    • If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

    編集

  3. Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

    • Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

    • The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

    編集

  4. Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel. Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel.

    • Lay the iOpener over the plastic tab to loosen the adhesive. Let the bag sit on the device for approximately 90 seconds before attempting to open the panel.

    編集

  5. Use a plastic opening tool to pull the rear plastic cover away from the device until there is enough room to insert a spudger. Insert a spudger under the cover, then pry it up and away from the device. Remove the rear plastic cover from the iPod.

    • Use a plastic opening tool to pull the rear plastic cover away from the device until there is enough room to insert a spudger.

    • Insert a spudger under the cover, then pry it up and away from the device.

    • Remove the rear plastic cover from the iPod.

    • Be very careful in removing the plastic cover as the bluetooth antenna is adhered to it.

    編集

  6. Gently bend the Bluetooth antenna to the right, out of the way of the screws in the bottom of the device.

    • Gently bend the Bluetooth antenna to the right, out of the way of the screws in the bottom of the device.

    • Remove the single 1.4 mm Phillips #000 screw from the black plastic spacer.

    編集

  7. Use a plastic opening tool to remove the black plastic spacer from the Nano. Use a plastic opening tool to remove the black plastic spacer from the Nano.

    • Use a plastic opening tool to remove the black plastic spacer from the Nano.

    編集

  9. Remove the two 2 mm Phillips #000 screws from the bottom of the case.

    • Remove the two 2 mm Phillips #000 screws from the bottom of the case.

    編集

  10. Insert a plastic opening tool into the seam between the white plastic front panel and the rear case. Slide the opening tool along the edge of the front panel to free it from clips and adhesive.

    • Insert a plastic opening tool into the seam between the white plastic front panel and the rear case.

    • Slide the opening tool along the edge of the front panel to free it from clips and adhesive.

    編集

  11. Use a spudger to press the midframe screw tab up and out of the rear case.

    • Use a spudger to press the midframe screw tab up and out of the rear case.

    編集

  12. Use a metal spudger to carefully pry near the Lightning connector and under all parts of the front panel assembly: the front glass/digitizer, the LCD display and the metal midframe.

    • Use a metal spudger to carefully pry near the Lightning connector and under all parts of the front panel assembly: the front glass/digitizer, the LCD display and the metal midframe.

    • The adhesive under the metal midframe/display assembly is quite strong and the components are fragile, so go slowly and gently. Make sure you do not bend the LCD screen.

    編集

  13. Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device. Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device.

    • Continue prying along the edges under the front panel assembly, releasing the clips and adhesive along the sides of the device.

    編集

  14. Pull the front panel assembly slightly down and partially out of the device. You only need to open the device enough to gain access to the display cable connectors near the sleep/power button.

    • Pull the front panel assembly slightly down and partially out of the device.

    • You only need to open the device enough to gain access to the display cable connectors near the sleep/power button.

    • Do not separate the two halves entirely, they are still connected by several cables.

    編集

  15. Use a spudger to release the digitizer cable and display data cable connectors. Use a spudger to release the digitizer cable and display data cable connectors.

    • Use a spudger to release the digitizer cable and display data cable connectors.

    編集

  16. Gently unfold the two halves of the device to access the internal components.

    • Gently unfold the two halves of the device to access the internal components.

    • Do not try to completely separate the two sections, yet, as they are still attached via a soldered cable.

    編集

  17. Pull up on the battery pull tab to free the battery from its adhesive. Flip the battery over into the rear case for safekeeping.

    • Pull up on the battery pull tab to free the battery from its adhesive.

    • Flip the battery over into the rear case for safekeeping.

    編集

  18. Completely separate the front panel assembly from the rest of the device.

    • Completely separate the front panel assembly from the rest of the device.

    編集

  19. Remove the 1.4 mm Phillips #000 screw from the antenna cable.

    • Remove the 1.4 mm Phillips #000 screw from the antenna cable.

    編集

  20. Release the Bluetooth antenna connector cable with a spudger. Remove the antenna from the device.

    • Release the Bluetooth antenna connector cable with a spudger.

    • Remove the antenna from the device.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

3他の投稿者と一緒に

Sam Goldheart

メンバー登録日: 2012年10月18日

393,489 ポイント

545のガイドは作成済み

バッジ: 48

+45 個以上のバッジ

チーム

iFixit iFixit人のメンバー

Community

108 メンバー

9,876のガイドは作成済み

2 件のコメント

コメントを追加

Kann man irgentwo bluetooth antennen nachbestellen ?? Meine antenne ist beschädigt und ich habe nun kein bluetooth mehr an meinen ipod nano 7

Dany Gaud - 返信

Upset that iFixit doesn’t hold this part (the bluetooth antenna) in their inventory, especially because it’s so easy to break when opening the device.

Pierre Souloumiac - 返信

コメントを追加

統計データを表示:

過去 24時間: 3

過去 7 日: 8

過去 30 日: 48

今までの合計 6,790