はじめに

iPod Nanoを落としてしまいましたか?

変形してしまったガラスパネルを交換するには、このガイドを使用してください。

iPod用開口ツールの端を、外装ケースと上部のベゼルの隙間に挿入します。
  • iPod用開口ツールの端を、外装ケースと上部のベゼルの隙間に挿入します。

  • 上部のベゼルをディスプレイリテーナに固定している接着剤からはがします。

  • この時点で、ホールドスイッチスライダは完全に外れており、落下する可能性があります。注意して作業を進めてください。

Be sure to use the smaller iPod opening tool and press it in FIRMLY in order to get enough leverage to get under the bezel and pry it off. Adhesive is very strong, so don't be afraid to use a little bit of force.

captcarl13 - 返信

ホールドスイッチスライダーをNanoの上部から取り外します。
  • ホールドスイッチスライダーをNanoの上部から取り外します。

コメントを追加する

  • ディスプレイリテーナの両端から角度の付いた2本のプラスネジを取り外します。

  • これらのネジは非常に小さく、容易に頭が潰れます。

Be sure to use a good phillips #00 screwdriver here, or you run the risk of stripping the very small screws.

iTronics Repair - 返信

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

bodieg - 返信

Quote from bodieg:

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

Step 12 is misleading as it does not show to remove the screen from the metal frame.

bodieg - 返信

Sorry guys, but the explanations are really bad. Go onto youtube and watch it. This site misses heaps of steps. I just broke my iPod :(

S Mile - 返信

Like others have noted, screws are covered in adhesive and difficult to remove. Take extreme care to not strip the heads. I'd suggest using a very small flathead to scrape some of the adhesive off before attempting to remove the screws.

captcarl13 - 返信

a 1mm slotted screwdriver will work in a pinch, but be carefull and make sure you get the angle just right

andrew - 返信

The tools list doesn't say you need an iPod opener to, nor does the parts list day you'll need a new click wheel, though this is called ”...click wheel REPLACEMENT​”. I don't get the feeling these are very trustworthy instructions, ESPECIALLY after having read other comments. I'd say BEWARE, and look at a variety of resources to get a much more comprehensive picture.

Skyfire - 返信

Actually, the screws are not aligned with the edges of the iPod, which means that you must not try to unscrew them vertically. If you do there is a good chance that you damage the head of the screws. Thus look carefully with a torch to see at what angle you have to unscrew them.

Fabrice Sarelli - 返信

Actually, the screws are not aligned with the edges of the iPod. That means that if you try to unscrew them vertically, there is a good chance that you damage the head of the screws. Thus, look carefully with a torch to see exactly at what angle you need to unscrew them safelly.

Fabrice Sarelli - 返信

Everything was good up to this point. I could barely see the screws and ended up stripping them. Just gave up at this point and threw the

Ipod on the ground and stomped on it.

gonzalo gonzalez - 返信

I agree with several other contributors here, that a properly sized flat screwdriver *that is not worn* held at the correct angle is a better option than a phillips because the screw head is filled in with adhesive tape. BEWARE: The screws on the top and bottom outer edges are not parallel to the case. They are offset by 25 or 30 degrees, with the tips of the screws pointing out towards the outer edge of the case with respect to where the heads are. Use something to get magnification so you can really see how your screwdriver fits, and whether it’s engaged. An undamaged and properly sized standard screwdriver held in the appropriate orientation will readily remove the top and bottom side screws without stripping and with very little force. Feel for engagement — press the screwdriver in just enough to get past the adhesive. Not much torque or pressure is required — just a good fit. You must have the right tools to do this job successfully, and look under high magnification. Align your screwdriver!

Barry L. Kramer - 返信

  • 外装とディスプレイリテーナーの間にiPod用の開口ツールを挿入します。

  • このツールを使用して、ディスプレイアセンブリをケースからわずかに引き出します。

  • ディスプレイリテーナはディスプレイの上端を支点にして回転させないでください。薄いスチール製のブラケットに取り付けられています。

  • ホールドスイッチケーブルが傷つきやすいので、ディスプレイリテーナを強制的に取り外さないでください。

I found I had to gently pry the retainer open with a craft knife (xacto knife?) as the plastic opener tool was too blunt or soft to get any purchase...

aaaidan - 返信

My nano had a "swollen" battery which wedged the LCD between battery and front glass. As a result, this step didn't work, I couldn't pull out the TFT and botched case, TFT and TFT frame until it came out. Telltale sign was a display that looked like there is a water between glass and LCD. The other nanos I've opened didnt have this problem and came out effortlessly, so if yours is stuck, don't feel bad, there's not much you can do!

oliver - 返信

  • ディスプレイを本体からスライドさせます。表示データケーブルがその移動を制限するまで約1.2cm移動します。

  • 非常に薄い表示データケーブルなので必要以上に引っ張らないこと。

I have several problems in taking it out. I don't know if it is dued to the glue that the iPod has inside. Could you help me. Thanks

Hector - 返信

instructions say 5" (inches) it really means 5mm

pedalsandpicks - 返信

Quote from pedalsandpicks:

instructions say 5" (inches) it really means 5mm

If you're gonna repair the way you read it will get you nowhere: the text reads .(as point)5 inch. Which is about 12mm.

Frank veenis - 返信

The glass panel can be very difficult to get moving requiring a lot of downward force. I have found good old fashioned spit to be very useful here.Just lick both thumbs and rub on fingers until just sticky enough.

This willl move the glass.

Pete Green - 返信

  • できるだけディスプレイをケースから引き出した状態で、ガラスパネル下端がわずかに(〜1 mm)飛び出すまで静かに押してください。

  • ガラスパネル下端に親指をあてて、上端がケースから飛び出すまでガラスパネルを下方向にスライドさせます。

I found the adhesive (or fit) quite strong. Pushing on the bottom part of the glass created a small gap at the top, which I could fit a craft knife (xacto blade) into. This made it easier to carefully lever the glass out for me.

aaaidan - 返信

I slipped and broke the LCD. So !#^&@@ off. What an absolute bastard of a job!

lf - 返信

What is the "rear edge" of the nano? Can this be a bit clearer please? Maybe a video of this step would be a good idea. Then again, since Apple owns this site, I guess that's not gonna happen, is it?

lf - 返信

I don't see "rear edge" anywhere in the instructions. I do see "lower edge" a few times and it looks pretty clear to me. I did this repair a couple years ago without much trouble.

Rene Jeddore -

You could do all these steps and really mess up your nano. Instead of disassembling the iPod, carefully remove the remnants of the old glass which I assumed you have cracked. With the new glass in hand CAREFULLY sand one edge of the glass evenly. I used my fine grinder on my dremel tool. After assuring a snug fit I removed the adhesive and installed the glass. Looks great and functional and I didn't ruin my iPod in the process. And when I said sand one edge I mean one of the edges that has a "lip" on it. The other lip you can slide right in and push gently down for a nice fit. Do not remove the adhesive until you are sure of a good fit. This is a quick fix for those who are too queezy to take apart their device.

Jim - 返信

  • ガラスパネルを本体から取り出します。

  • ガラスパネルを取り付ける前に、ディスプレイの表面とパネルの内部をきれいに掃除してください。電源を入れたときに埃や指紋が目立ちます。

コメントを追加する

まとめ

再組み立てをする際は、これらのインストラクションを逆の順番に従って作業を進めてください。

28 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 貢献してみませんか?
翻訳を始める ›

Walter Galan

564,782 ポイント

1,203のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 20

過去 30 日: 134

今までの合計 34,465