メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

iPod Nano 4th Generation Click Wheel Replacement

作成者： Walter Galan (そして 4 人のその他投稿者)
  • コメント: 54
  • お気に入り: 25
  • 完了: 47

難易度

難しい

手順

21

所要時間

必要時間を提案??

セクション

4

フラグ

0

はじめに

Replace a broken click wheel to regain control of your Nano.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel. Pry the top bezel off the adhesive securing it to the display retainer.

    • Insert the edge of an iPod opening tool into the gap between the outer case and the top bezel.

    • Pry the top bezel off the adhesive securing it to the display retainer.

    • At this point the hold switch slider is free and may fall. Be careful not to lose it.

    編集

  2. Remove the hold switch slider from the top of the Nano.

    • Remove the hold switch slider from the top of the Nano.

    編集

  3. Remove the two angled Phillips screws from the two corners of the display retainer.

    • Remove the two angled Phillips screws from the two corners of the display retainer.

    • These screw heads are extremely small and easily stripped.

    編集

  4. Insert an iPod opening tool between the outer case and the display retainer.

    • Insert an iPod opening tool between the outer case and the display retainer.

    • Use the tool to slide the display assembly out of the case slightly.

    • Do not rotate the display retainer about the top edge of the display, as it is attached to a thin steel bracket that is easily broken.

    • Do not forcefully remove the display retainer, as the hold switch cable is liable to snap.

    編集

  5. Slide the display out of the Nano. It will move about .5" until the display data cable limits its travel.

    • Slide the display out of the Nano. It will move about .5" until the display data cable limits its travel.

    • Do not put unnecessary tension on the very thin display data cable.

    編集

  6. With the display pulled out of the case as much as possible, gently press on the lower edge of the glass panel until it pops in slightly (~1 mm). Use your thumbs on the lower edge of the glass panel to slide the glass down and into the case until the top edge pops up out of the case.

    • With the display pulled out of the case as much as possible, gently press on the lower edge of the glass panel until it pops in slightly (~1 mm).

    • Use your thumbs on the lower edge of the glass panel to slide the glass down and into the case until the top edge pops up out of the case.

    編集

  7. Lift the glass panel out of the Nano.

    • Lift the glass panel out of the Nano.

    • Before reinstalling the glass panel, be sure to clean the face of the display and the inside of the panel as any dust or fingerprints will be annoyingly visible when the Nano is turned on.

    編集

  8. PCラップトップ用バッテリー

    An easy fix for a big power boost.

    ショップを見る

    PCラップトップ用バッテリー

    An easy fix for a big power boost.

    ショップを見る

  9. Use the edge of an iPod opening tool to separate the hold switch from the adhesive securing it to the top edge of the display.

    • Use the edge of an iPod opening tool to separate the hold switch from the adhesive securing it to the top edge of the display.

    • The hold switch ribbon cable is extremely fragile and easily broken. Work gently.

    編集

  10. Peel back the Kapton tape covering the display data cable socket.

    • Peel back the Kapton tape covering the display data cable socket.

    編集

  11. While holding the light colored socket down with one finger, use the tip of a spudger to flip the ZIF cable lock up toward the bottom of the Nano.

    • While holding the light colored socket down with one finger, use the tip of a spudger to flip the ZIF cable lock up toward the bottom of the Nano.

    編集

  12. Use an iPod opening tool to peel the display data cable off the thin metal plate attached to the display.

    • Use an iPod opening tool to peel the display data cable off the thin metal plate attached to the display.

    • Be careful not to rip the display data cable.

    編集

  13. Pull the display out of the Nano, minding the hold switch cable that may get caught.

    • Pull the display out of the Nano, minding the hold switch cable that may get caught.

    • As you pull the display out of the case, be careful not to break the hold switch cable.

    編集

  14. Insert an iPod opening tool between the bottom bezel and the dock connector. Separate the bottom bezel from the adhesive securing it to the Nano and set it aside.

    • Insert an iPod opening tool between the bottom bezel and the dock connector.

    • Separate the bottom bezel from the adhesive securing it to the Nano and set it aside.

    編集

  15. Remove the three Phillips screws along the bottom of the Nano.

    • Remove the three Phillips screws along the bottom of the Nano.

    • These screw heads are extremely small and easily stripped.

    • The slightly longer of the three screws belongs in the middle.

    編集

  16. Use an iPod opening tool to pry the aluminum dock bezel out of the Nano. The dock bezel is very thin cast aluminum. To avoid breaking it, do not excessively flex it during removal.

    • Use an iPod opening tool to pry the aluminum dock bezel out of the Nano.

    • The dock bezel is very thin cast aluminum. To avoid breaking it, do not excessively flex it during removal.

    編集

  17. Use the flat end of a spudger to separate the battery from the adhesive securing it to the outer case. The lithium polymer battery used in the Nano is very flexible. Try not to deform it excessively while separating it from the outer case. Use the flat end of a spudger to push the logic board assembly and battery slightly out of the bottom of the Nano. Stop once it pops out a little bit.

    • Use the flat end of a spudger to separate the battery from the adhesive securing it to the outer case.

    • The lithium polymer battery used in the Nano is very flexible. Try not to deform it excessively while separating it from the outer case.

    • Use the flat end of a spudger to push the logic board assembly and battery slightly out of the bottom of the Nano. Stop once it pops out a little bit.

    編集

  18. Use the edge of an iPod opening tool to peel the click wheel ribbon cable and its ZIF socket off the dock connector.

    • Use the edge of an iPod opening tool to peel the click wheel ribbon cable and its ZIF socket off the dock connector.

    編集

  19. Use the edge of an iPod opening tool to flip the ZIF cable lock up toward the headphone jack. Use the edge of an iPod opening tool to flip the ZIF cable lock up toward the headphone jack.

    • Use the edge of an iPod opening tool to flip the ZIF cable lock up toward the headphone jack.

    編集

  20. Use a pair of tweezers to slide the click wheel ribbon cable out of its socket.

    • Use a pair of tweezers to slide the click wheel ribbon cable out of its socket.

    • Before proceeding, be sure that both the click wheel ribbon cable socket and its cable are freed from the adhesive securing them to the dock connector and logic board.

    • Peel back the cable on both ends!

    編集

  21. Pull the logic board assembly out of the outer case, minding the hold switch and click wheel cables that may get caught.

    • Pull the logic board assembly out of the outer case, minding the hold switch and click wheel cables that may get caught.

    • When reassembling, ensure the click wheel cable is toward the front of the Nano and not in the grooves on the side. If it is in the groove you will probably cut it while sliding the logic board into place.

    編集

  22. Press down firmly around the perimeter of the click wheel to separate it from the adhesive securing it to the outer case. This requires a good amount of force. Work slowly.

    • Press down firmly around the perimeter of the click wheel to separate it from the adhesive securing it to the outer case.

    • This requires a good amount of force. Work slowly.

    • It may be helpful to use an edged tool to separate the adhesive from the click wheel on the inside of the Nano while pressing it down from the outside.

    • Remove the click wheel from the inside of the Nano.

    • Be careful not to let the click-wheel slide on the metal plate supporting it, as it will break the flat cable. Apply force perpendicular to the click-wheel.

    編集
まとめ

To reassemble your device, follow these instructions in reverse order.

47 の人々がこのガイドを完成させました。

作成者

4他の投稿者と一緒に

Walter Galan

604,011 ポイント

1,203のガイドは作成済み

バッジ: 53

+50 個以上のバッジ

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 4

過去 7 日: 25

過去 30 日: 137

今までの合計 136,376