修理を始めるには コミュニティ ストア

iPhone 4 Speaker Enclosure Assembly Replacement

必要条件のみ
この修理ガイドは、他のガイドの前提条件として使用されます。それ自体は不完全で、単独で使用されることはありません。

はじめに

Prereq with logic board still in.

必要な工具と部品

  1. iPhone 4 Speaker Enclosure Assembly Replacement, Speaker Enclosure Assembly: 手順 1、 2の画像 1 iPhone 4 Speaker Enclosure Assembly Replacement, Speaker Enclosure Assembly: 手順 1、 2の画像 2

    • Remove the following two screws:

    • One 1.2 mm Phillips

    • One 1.6 mm Phillips

    • Remove the thin steel dock connector cable cover from the iPhone.

    • Before reassembly, be sure to clean all metal-to-metal contact points on the dock connector cable cover with a de-greaser such as windex. The oils on your fingers have the potential to cause wireless interference issues.

    翻訳

  2. iPhone 4 Speaker Enclosure Assembly Replacement: 手順 2、 2の画像 1 iPhone 4 Speaker Enclosure Assembly Replacement: 手順 2、 2の画像 2

    • Use a plastic opening tool to gently pry the dock cable connector up off the logic board from both short ends of the connector.

    翻訳

  4. iPhone 4 Speaker Enclosure Assembly Replacement: 手順 3、 2の画像 1 iPhone 4 Speaker Enclosure Assembly Replacement: 手順 3、 2の画像 2

    • Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure.

    • Do not use excessive force to peel the dock ribbon cable off the logic board. Doing so may tear the cable.

    翻訳

  5. iPhone 4 Speaker Enclosure Assembly Replacement: 手順 4、 1の画像 1

    • Use a plastic opening tool to pry the lower antenna connector up off its socket on the logic board.

    翻訳

  6. iPhone 4 Speaker Enclosure Assembly Replacement: 手順 5、 1の画像 1

    • Remove the following screws securing the speaker enclosure assembly to the outer case:

    • One 1.9 mm Phillips screw

    • One 2.4 mm Phillips screw

    翻訳

  7. iPhone 4 Speaker Enclosure Assembly Replacement: 手順 6、 3の画像 1 iPhone 4 Speaker Enclosure Assembly Replacement: 手順 6、 3の画像 2 iPhone 4 Speaker Enclosure Assembly Replacement: 手順 6、 3の画像 3

    • Use a plastic opening tool to lift the speaker enclosure assembly out of the case, being sure not to damage the EMI fingers on the attached Wi-Fi antenna.

    • Remove the speaker enclosure assembly.

    • Before reinstalling the speaker enclosure assembly's screws, be sure the Wi-Fi grounding fingers are installed below the lip in the iPhone's metal case as seen in the third picture.

    • Before reassembly, be sure to clean all metal-to-metal contact points between the grounding fingers of the Wi-Fi antenna and the case of the iPhone with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause wireless interference issues.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Walter Galan

694,773 ポイント

1,203のガイドは作成済み

バッジ: 54

+51 個以上のバッジ

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 4

過去 30 日: 4

今までの合計 63