メインコンテンツにスキップ

iMac Intel 27" EMC 2546 Logic Board Assembly Replacement

必要条件のみ
この修理ガイドは、他のガイドの前提条件として使用されます。それ自体は不完全で、単独で使用されることはありません。

必要な工具と部品

  1. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement, Logic Board Assembly: 手順 1、 3の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement, Logic Board Assembly: 手順 1、 3の画像 2 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement, Logic Board Assembly: 手順 1、 3の画像 3
    • Use the flat end of a spudger to disconnect each of the four antenna connectors from the AirPort/Bluetooth card.

    • Note the original positions for each connector when reconnecting the cables. From left to right on the card, the antennas are connected in the following order:

    • Leftmost

    • Top

    • Upper right

    • Lower right

  2. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 2、 3の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 2、 3の画像 2 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 2、 3の画像 3
    • This is a delicate connection that can be easily broken.

    • Flip up the metal retaining bracket on the iSight camera cable.

    • Pull the camera cable connector straight out of its socket, toward the top of the iMac.

  3. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 3、 3の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 3、 3の画像 2 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 3、 3の画像 3
    • Use the flat end of a spudger to disconnect the headphone jack cable connector from its socket on the logic board.

    • Gently push the cable out of the way.

  4. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 4、 2の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 4、 2の画像 2
    • Remove the following screws from the front of the logic board:

    • Two 23.7 mm T10 screws

    • Four 7.4 mm T10 screws

    • One 20.8 mm T25 spacer screw

    • One captive T10 screw

    • This screw is beneath a hole in the logic board. You'll need a fixed screwdriver or the 60 mm extension from an iFixit driver kit to reach it.

  5. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 5、 3の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 5、 3の画像 2 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 5、 3の画像 3
    • The hard drive SATA cable can't be removed just yet, but will get in the way of removing the logic board.

    • Pull the cable and connector through the right hard drive bracket. Move the cable to the right side of the iMac, out of the way of the exhaust port.

  6. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 6、 1の画像 1
    • Remove two 5.7 mm T10 screws from the top of the heat sink exhaust duct.

  7. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 7、 3の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 7、 3の画像 2 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 7、 3の画像 3
    • Tilt the logic board slightly forward.

    • Lift the logic board straight up and out of the iMac. Be careful not to snag on any of the screw posts attached to the inside of the rear case.

  8. iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 8、 2の画像 1 iMac Intel 27" EMC 2546 Logic Board Assembly Replacement: 手順 8、 2の画像 2
    • When reassembling your iMac, be very careful to align the exterior I/O ports correctly. The logic board can sit crooked even when secured with all its screws.

    • You can use a USB flashdrive or ethernet cable to ensure the logic board is seated correctly while you screw it in.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

4人の作成者と共同で作成されました。

Andrew Optimus Goldheart

メンバー登録日: 10/17/09

502,332 ポイント

407のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Staff

136 メンバー

16,573のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 2

今までの合計 404